Page 11
Important charging notes:
1.
Longest life and best performance can be obtained if the battery pack is charged with the air temperature is between 50°F (10°C) and
80°F (26°C).
2.
The charger and battery pack may become warm to the touch while charging. This is normal and does not indicate a problem. Ensure the
vents are not blocked to allow cooling.
3.
The battery pack should be recharged when it no longer powers the equipment. Do not continue to attempt using the battery if low power
is indicated. You may recharge a partially discharged battery pack without damaging the battery pack.
4.
Do not freeze or submerge the charger in water or any other liquid.
Warning:
Shock Hazard. Do not allow any liquid to get inside the charger. Never attempt to open the battery pack for any reason. If the plastic housing of the
battery pack breaks for cracks, return to a recycling center and replace the charger.
The receiver is designed to power all High-Flo 12V pumps. The receiver will output 12V DC and is limited to 15A max. current.
To install the receiver, the pump will be removed. The base plate and adjustable support will be placed un-
der the pump and screwed down with the longer screws supplied in the kit. The receiver has already been
pinned to the base plate, but it can be removed to make screw installation easier by sliding the pin out. Then
the receiver is slid into the adjustable support bracket. It will click into the first position, sized for the Pro
Series pumps and the 4.5 pump.
2.4 GPM Pump w/Manifold Configuration:
Place pump on base plate and screw down to tank or frame, using the (3) #10-24 x 3/4” and (1) #10-24 x 1”
screws. The 1” screw goes through the manifold support bracket. Click the receiver into the second position
of the adjustable support.
Operating Procedure:
1.
Charge the battery following the charging procedure.
2.
Ensure all fasteners are tight and pump connections are secure.
3.
Install the battery ensuring the base is connected and it is fully seated.
4.
Press the power button and confirm the green LED turns on. Signaling the power is on.
5.
Test the remote by pressing the OFF button on the remote and both green and red receiver LEDs will turn on. Signaling the power
output is off while the power is on.
6.
Press the ON button on the remote. The red LED will turn off and power output will return.
7.
Press the power button again to turn the receiver off.
8.
Connect the receiver 2-pin connector to the pump.
9.
Press the power button to turn the receiver on and the pump will run.
10. When spraying is complete press the power button to turn off the receiver.
11. Recharge the battery to properly maintain the battery pack.
Receiver Diagnostics:
The receiver is designed to detect certain problems that can arise with the battery packs or the pump. Problems are indicated by the red and green
LEDs.
Battery Life
When the battery is approaching fully discharged, the green LED will begin to flash. When the battery is fully discharged, power will stop
being supplied to the pump and the green LED will continue flashing. Power off the receiver and charge the battery.
Protection Mode
When the receiver identifies a problem with the pump, the power output will stop and the red LED will flash and the green LED will remain
illuminated. The red LED will blink in cycles to identify the problem. Press the power button turning the receiver off to reset the system. Wait
30 seconds and press the power button to resume operation.
Red LED flashing two times:
Open circuit protection. The receiver power is on without powering consumption.
Red LED flashing three times:
Incorrect voltage. Voltage being supplied to the receiver is outside the range.
Red LED flashing four times:
High current protection. The pump has drawn current above the limit.
Red LED flashing ten times:
Temperature protection. The system has measured the temperature to be outside safe operating
temperatures.
Leaving the battery in the charger.
The charger and battery pack can be left connected with the green LED indicating the charger is maintaining the battery continuously. The charger will
keep the battery pack fresh and fully charged.
