background image

Page 6 

 

Piston Type Pressure Relief/Regulating Valves 

Bypasses excess fluid. Adjustable to maintain control of line pressure at any pressure within the valve operating range. 

Selected pressure setting firmly held in place by locknut. Extra large passages to handle large flows. 

 

Polypropylene with stainless steel spring 

 

Excellent chemical resistance 

 

EPDM O-Rings 

 

Fore pressure to 150 p.s.i. 

 

1/4” port for pressure gauge 

 

3/4” NPT (M) inlet & (F) outlet connections

 

 

 

 

 

 

 

 

 

 

 

 

 

* * Available ONLY in Repair Kit 

♦ ♦ ONLY Available in Complete Assembly

 

RH boom is ‘selected’

 

Cast Iron 6-Roller Pump Assembly 

#5271706 (Hypro Mfg. Part # 6500C) 

* * = Available ONLY in Repair 

Parts Kit #7771795 (3430-0380) 

Consists of Rollers, O-Ring & 

Viton Seals 

 

♦ ♦ Available ONLY in Complete 

Assembly 

TeeValve Control Valve Model: AA17L (5143295) 

Model AA17L, used for selective control of 3-section boom sprayers 

at pressures up to 300 PSI. 

 

 

Use to open any of three boom sections lines in any 

desired combination.

 

 

Raise lever to open, lower lever to close the valve 

without changing the indexed position.

 

 

Aluminum construction with stainless steel and plastic 

internal parts for maximum corrosion resistance. 

 

3/4” NPT Inlet/Outlet, 3 boom outlet and accessory 

outlet. 

 

1/4” NPT Gauge Port 

RH boom is ‘activated’

 

Содержание 110-3PT-17N













Отзывы: