Fimap BMg 50 Orbital, Руководство по эксплуатации и обслуживанию

Страница: 19 / 52

ASSEMBLING THE ABRASIVE PAD (ORBITAL VERSION)
To fit the abrasive pad on the brush head body, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION: these operations must be carried out using protective gloves to avoid any possible contact with the edges
or tips of metal objects.
3. Stand on the left side of the machine.
4. With the brush head in its raised position, insert the abrasive pad into the lodging present on the brush head body ( Fig.1 ).
1
ASSEMBLING THE SQUEEGEE BODY
For packaging reasons, the squeegee body comes disassembled from the machine. In order to mount it on the squeegee support, do the
following:
1. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION:
these operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal
objects.
2. Unscrew the knobs (1) in the squeegee body pre-assembly ( Fig.1 ).
3. First, insert the left pin (2) on the squeegee body into the left slit (3) in the squeegee support ( Fig.2 ), so that the bushing adheres to the
walls of the slit in the squeegee support.
4. Repeat the same operation for the right pin.
5. Insert the vacuum tube (4) in the sleeve (5) in the squeegee body ( Fig.3 ).
N.B.: Although the squeegee comes pre-adjusted, it is nevertheless recommended to read the section titled “ADJUSTING THE
SQUEEGEE BODY'S RUBBER BLADES”.
1 2 3
5
4
1
3
2
PREPARING TO WORK
Before beginning to work, it is necessary to:
1. Make sure the recovery tank is empty. If this is not the case, empty it (read “ EMPTYING THE RECOVERY TANK ”).
2. Check that the amount of detergent solution present in the solution tank is sufficient for the type of work to be performed. If this is not the
case, top up the solution tank (see the sections titled “ FILLING THE SOLUTION TANK ” and “ DETERGENT SOLUTION ”).
3. Check that the squeegee rubbers are in good working condition. If not, carry out maintenance (see “ REPLACING THE SQUEEGEE BODY
RUBBER BLADES ”).
4. Check that the condition of the brushes is suitable for the work to be carried out; if not, carry out the necessary maintenance (read the
paragraphs concerning the assembly of the brushes or of the abrasive pad).
5. Check that the main switch is set to “0", turn the key (1) a quarter turn anti-clockwise ( Fig.1 ) . With the machine off, remove the key from the
instrument panel.
6. Press the recovery tank release lever (2) and turn the recovery tank into the maintenance position ( Fig. 2 ).
CAUTION: the following operations must be carried out by qualified personnel. An incorrect connection of the connector may cause
problems with machine functioning.
7. Connect the battery connector from the main machine system connector ( Fig.3 ).
8. Rotate the recovery tank into the working position ( Fig.4 ). Make sure that the recovery tank retainer system is correctly engaged.
9. Move to the right rear part of the machine and check that the electro-brake, present in the traction gear motor, is not engaged. Turn the lever
(3) clockwise ( Fig.5 ).
10. Move to the front of the machine and check that the water system filter cap (4) is closed, otherwise tighten it ( Fig.6 ).
11. Move to the front left-side of the machine and check that the water tap is fully open, move the water adjustment knob (5) in the direction
shown by the arrow ( Fig.7 ).
12. Move to the rear of the machine a check that the cap of the recovery tank drainage tube (6) is closed. If it isn't, close it ( Fig.8 ).
6
4
5
3
1
1
4 2 3
2
19