e-mail: [email protected]
www.fim-umbrella.com
ASSEMBLY INSTRUCTIONS
COMPONENTS (Pict. 1, 2):
Pict. 1A – FLEXY TWIN WITH A SINGLE CANOPY
(Fig. 2A) Nr 1
sliding canopy (A)
with the
crossbar (C)
(Fig. 3A) Nr. 1
Upright pole (DA)
(Fig. 4a) Nr 1
Lever group (E) and a bag containing Allen keys of 3 (e3)- 4 (e4)- 5 (e5)
(Fig. 5A) Nr 1
hot dip galvanized steel base (F),
set of
steel
ballasts, a bag of hardware (H) containing 6 feet (f),
4 screws M 10x30 (d), an Allen key 6 (e6).
Pict. 1B – FLEXY TWIN WITH A DOUBLE CANOPY
(Fig. 2B) Nr 2
sliding canopies (A)
with the
crossbar (C)
(Fig. 3B)
Nr. 1
Upright pole (DB)
(Pict. 4B) Nr 2
Lever groups and a bag containing Allen keys of 3 (e3)- 4 (e4)- 5 (e5)
(Pict. 5) Nr 1
hot dip galvanized steel base (F),
set of
steel
ballasts, a bag of hardware (H) containing 6 feet (f), 4
screws M 10x30 (d), an Allen key 6 (e6).
FREESTANDING BASE ASSEMBLY AND POSITIONING (Pict. 6A, 6B and 6C)
Take out the content of the
bag of hardware
(H)
.
Screw the
feet (f)
to the
base (F),
put the base where you want to assemble Flexy Twin. Make sure that the base is
level
using
the
adjustable
the
feet (f).
Mount
the
upright pole (DA) or (DB)
to the
base (F)
with 4
screws (d)
and tighten them well with an
Allen key (e6).
Place
the
set of
steel
ballasts
(G’) (G’’)
on the carrier plate
and bolt the ballasts
firmly down
.
MOUNTING THE SLIDING CANOPY (Pict.7,8,9)
Remove 2
screws (h)
from the
crossbar (C)
Remove
the
screw (i)
and
washer (M)
from the
lever group (E)
with an
Allen key (e3).
Insert the
crossbar (C)
into the sliders of the
canopy (A)
and make sure that the two ends of the cord are not tangled together and
stay parralel.
Fix the
lever group (E)
to the
crossbar (C)
with the
screws (h).
Δ CAUTION: tighten the screws with an Allen key (e5).
MOUNTING THE SLIDING CANOPY ON THE POLE (Pict. 9,10,11)
CAUTION: To avoid damage the operation has to be done simultaneously by two persons with 2 step ladders.
Raise the sliding canopy and join the
lever group (E)
to the
pin (P)
of the
upright pole (DA
or
DB).
Remount the
flange (I)
and fix everything with
2 screws (g).
CAUTION:
when the
lever group (E)
is joint to the
pin (P)
push the end of the canopy facing up while
2 screws (g)
are
pulling. It should be firmly tightened.
Pull the lever group and tilt the canopy on one side. Insert the
washer (M)
into the
buttonhole (R)
and fix it with the
screw (i).
CAUTION:
The procedure is necessary for the wind resistance.
Push the slider
(N’)
against the
lever group (E)
and screw the handwheel stem in the hole of the
crossbar (C).
Remove the
weight (S)
applied on the double cord, the weight is divided in 2, put it back after the
cord (O)
is inside the
pulley
(T).
Important
:
it is essential for the subsequent smooth operation of the canopy that the two ends of the cord are kept extended
and not tangled together .
Содержание Flexy Twin
