Fiery DocuColor 3535 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 116

Fiery DocuColor 3535 Скачать руководство пользователя страница 25

2

2-1

Fiery on a TCP/IP network with Windows NT 4.0/ 2000/XP

This chapter describes environments that typically include one or more network
servers—Novell NetWare servers and Windows NT 4.0/2000 servers—that share
printing to the Fiery. It describes setting up servers that use IPX/SPX or TCP/IP
protocols for communicating with the Fiery. In addition, it includes guidelines for
setting up direct communication from Windows NT 4.0/2000/XP workstations or
UNIX workstations, where a network server is optional. This chapter also outlines the
requirements for users to print to the Fiery and run Fiery utilities and Fiery WebTools.

The Fiery can accept jobs concurrently from NetWare, Windows NT 4.0/2000, and
AppleShare servers, as well as jobs sent directly from Windows NT 4.0/2000/XP or
UNIX workstations. Because AppleShare servers require no special configuration, they
are not discussed in this chapter, except for use in a Windows NT 4.0/2000
environment (see

“Fiery on a TCP/IP network with Windows NT 4.0/ 2000/XP”

the following section).

If your network is based on Windows NT 4.0/2000, proceed to the following section.
For information on UNIX workstations, proceed to

.

Fiery on a TCP/IP network with Windows NT 4.0/
2000/XP

When a Windows NT 4.0/2000/XP computer is configured to connect to the
Fiery using TCP/IP, it can print directly to the Fiery. If the computer shares the
printer over the network, it is acting as a print server to Windows 9x/Me and
Windows NT 4.0/2000/XP clients. Client computers print to the Fiery by
printing to the Windows NT 4.0/2000 print server. You can then monitor and
control printing at the Windows NT 4.0/2000 server computer.

Typical system combinations are:

• Print server running Windows NT 4.0/2000 Server; clients running

Windows NT 4.0/2000/XP Workstation and Windows 9x/Me

With TCP/IP protocols loaded, you can run Fiery utilities and Fiery WebTools from a
Windows computer.

Chapter 2:
Setting up
Network Servers

«
...
23
24
25
26
27
...
»

Содержание DocuColor 3535





















































































































Отзывы:

Нет отзывов