FieldServer FS-8700-39 Скачать руководство пользователя страница 23

Страница: 23 / 25

FS-8700-39 EST3 Driver Manual

Page 23 of 25

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com

Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: [email protected]

Appendix C.1.2.

Output data format

Each output device is associated with a 16-bit value. This value consists of two byte fields, the command (LSB) and the
attribute (MSB).

FieldServer Data Array Object (16-bit)

Attribute (8-bit)

Command (8-bit)

These values are provided by the EST panel and are described in the EST3 ECP protocol specification as follows. These values
will be put in the Command field.

Command

Encode Value

Activate / Away

01h

Enable

02h

Restore / Disarm 11h
Disable

12h

The attribute byte must be set for writes to Relay, LED outputs and DeviceTest

For Relays, the attribute values are:

Attribute (Relay) Encode Value

Enable

Activate

101h

Restore

11h

Disable

12h

For LED’s, the attribute values are:

Attribute (LED) Encode Value

101h

Slow Flash

201h

Fast Flash

301h

Disable

12h

Enable

Off

For DeviceTest (Signature Devices Only), the attribute values are:

Attribute (DeviceTest)

Encode Value

TestActive1

Places the device in its primary active state (Alarm, Monitor, Supervisory, SecurityAlarm, etc

201h

TestTrouble

Places the device in CommonTrouble

301h

TestActive2

Places Security devices capable of tamper, in SecurityTamper.
Places sensors capable of PreAlarm in Prealarm

401h

Содержание FS-8700-39


























Результаты поиска

Содержание FS-8700-39

Отзывы:

Похожие инструкции для FS-8700-39

Бренды по названию

Популярные бренды

FieldServer FS-8700-39, Руководство пользователя

Результаты поиска

Содержание FS-8700-39

Отзывы:

Похожие инструкции для FS-8700-39

Бренды по названию

Популярные бренды