manualshive.com logo in svg

Fields Edge M220, Руководство оператора

Поделиться
Скачать
Fields Edge M220 Скачать руководство пользователя страница 14

14

Check for parts online at 

www.getfieldsedge.com

 or call 800-345-6007 M-F 8-5

Operator's Manual

String Mower M220

How to Replace the Drive Belt

To replace the drive belt, the mower head and shield must be 

removed as follows:  

SEE FIGURES 14 AND 15

1.   Remove the two screws that hold the rear of the shield to 

the mower housing.

2.   Remove the four bolts that hold the front of the shield 

and mower head to the mower housing.

3.   Raise the front of the mower housing and remove the 

drive belt. 

4.  Remove the “V” pulley from the idler bracket. 

NOTE:  On some models, it is necessary to loosen the 

mounting bolt for the drive pulley to remove the 

drive belt . Do not bend the belt guides. Use only 

OEM replacement belts. 

5.   To assemble the drive belt, reverse the above steps. Make 

sure all fasteners are tight. Make sure the mounting bolt 

for the drive pulley is tight. 

6.  Check the routing of the drive belt. Make sure the drive 

belt is inside of all belt guides as shown.

 

WARNING

BEFORE YOU REMOVE THE DRIVE BELT, 

DISCONNECT THE WIRE FROM THE SPARK PLUG.

 

IMPORTANT

TEST THE DRIVE SYSTEM. START THE ENGINE AND 

ENGAGE AND DISENGAGE THE MOWER HEAD 

SEVERAL TIMES. WHEN DISENGAGED, MAKE SURE 

THE MOWER HEAD COMPLETELY STOPS WHEN 

RESTING ON THE GROUND. IF THE MOWER HEAD 

CONTINUES TO ROTATE, TAKE THE MOWER TO AN 

AUTHORIZED SERVICE CENTER.

FIGURE 14:

 Mower Head Housing and Shield

BOLTS

DRIVE BELT

SHIELD

MOWER HEAD

BUMP HEADS

FIGURE 15:

 Routing The Drive Belt

DRIVE

BELT

RETURN

SPRING

“V” PULLEY

BELT

GUIDES

MOUNTING 

BOLT

DRIVE

PULLEY

Содержание M220

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды