Fieldmann FDW 202001-E, Руководство по эксплуатации

Страница: 12 / 178

EN 12
FDW 2001 E
12 EN Assembly instructions
Note:
The pressure of the spray on the surface you are cleaning increases as you move the
wand closer to the surface.
The high pressure setting is for cleaning and rinsing,
For high pressure operation, pull back the name of the variable spray lance.
USING THE DETERGENT BOTTLE ASSEMBLY
ATTENTION! NOTICE:
Use only approved pressure washer cleaners. Do not use bleach, chlorine, or any cleaners
containing acids.
Remove the lance
Remove the soap nozzle from the detergent bottle assembly and ensure the suction lube Is
property connected.
Fill the detergent bottle with suitable cleaning solution and replace the soap nozzle..
Assembly instructions | Starting
FDW 2001 E
14 EN Assembly instructions | Starting
ATTENTION!
CAUTION:
Damage may occur to painted surface if soap is allowed to dry on the surface. Wash and
rinse a small section at a time.
.Apply the solution to a DRY work surface.
Note:
WETTING THE SURFACE FIRST IS NOT RECOMMENDED, AS IT DILUTES THE
DETERGENT AND REDUCES ITS CLEANING ABILITY.
Allow detergent to remain on the surface for a short time before rinsing.
Rinse with clean water under high pressure. On a vertical surface, fi st rinse from the bottom
up, then rinse from the top down. Hold nozzle 6 – 8 in in (15-20 cm) from the work surface at
a 45° angle using the flat pray as a peeling tool rather than a scrub brush.
Note:
Ensure that the detergent injection system is completely clean prior to switching from
one detergent to another
6. STARTING
ATTENTION!
DANGER:
Risk of injury from spray. Always engage the trigger lock when gun is not in use. Failure to do
so could cause accidental spraying.
ATTENTION!
WARNING
Risk of Injury. Do not direct discharge stream at self or others.
ATTENTION!
WARNING
Risk of unsafe operation. Stand on a stable surface and grip gun/ spray wand fi mly with
both hands.
Connect the high pressure hose to the machine outlet. Ensure the threads are aligned
properly and the connection is secure.
Connect the garden hose to the connector on the back of the machine. Before connecting, run
water through the garden hose {not supplied) to flush cut a y foreign matter.
FDW 2001 E
14 EN Assembly instructions | Starting
ATTENTION!
CAUTION:
Damage may occur to painted surface if soap is allowed to dry on the surface. Wash and
rinse a small section at a time.
.Apply the solution to a DRY work surface.
Note:
WETTING THE SURFACE FIRST IS NOT RECOMMENDED, AS IT DILUTES THE
DETERGENT AND REDUCES ITS CLEANING ABILITY.
Allow detergent to remain on the surface for a short time before rinsing.
Rinse with clean water under high pressure. On a vertical surface, fi st rinse from the bottom
up, then rinse from the top down. Hold nozzle 6 – 8 in in (15-20 cm) from the work surface at
a 45° angle using the flat pray as a peeling tool rather than a scrub brush.
Note: Ensure that the detergent injection system is completely clean prior to switching from
one detergent to another
6. STARTING
ATTENTION!
DANGER:
Risk of injury from spray. Always engage the trigger lock when gun is not in use. Failure to do
so could cause accidental spraying.
ATTENTION!
WARNING
Risk of Injury. Do not direct discharge stream at self or others.
ATTENTION!
WARNING
Risk of unsafe operation. Stand on a stable surface and grip gun/ spray wand fi mly with
both hands.
Connect the high pressure hose to the machine outlet. Ensure the threads are aligned
properly and the connection is secure.
Connect the garden hose to the connector on the back of the machine. Before connecting, run
water through the garden hose {not supplied) to flush cut a y foreign matter.
FDW 202001-E