manualshive.com logo in svg

Field Controls UV-AIRE UV-E, Инструкция по эксплуатации, Страница: 5 / 8

Поделиться
Скачать
Field Controls UV-AIRE UV-E Скачать руководство пользователя страница 5

page 5

WARNING:

 

Never expose eyes or skin to UVC light from any source. Looking directly at the UVC light may cause permanent eye damage or blindness.

Never operate the UV-Aire Air Purifying System out of the plenum

. Avoid touching the glass portion of the lamp with your hands.

Swing securing bracket over end of lamp and hand-tighten the provided 

17. 

wing nut on stud. (See Figure 13) 

Plug ballast plug into end of lamp and reconnect power supply.  

18. 

(See Figure 14) 

Flip the red power switch to the on position. (Light on switch should be on 

19. 

indicating power.) 

Look through view port to be sure lamp is working.  You should see a 

20. 

blue glow. (The view port is covered with a plastic lens that blocks the 

UVC rays.) 

If the lamp is not glowing, make sure the wiring is correct and 

21. 

that the ballast is plugged in securely to lamp. If lamp still does 

not glow, contact technical support at 1-252-522-3031 for 

further assistance. 

After unit has been found to be working properly, note date of 

22. 

installation on inside cover, close cover and engage latch. Apply 

supplied wire tie to latch or other locking mechanism to  

provide safety.

Figure 13

Figure 14

BULB MOUNTING BRACKET SELECTION AND INSTALLATION

The UV-AIRE units come with an angled mounting bracket and flat mounting bracket to position the bulb either 

straight or at an angle.  Choose the bracket method best suited for your needs.  Refer to the configurations 

chart below when making your selection.

Good

Better

Standard 90° Installation

(Flat Bracket)

(Fits a minimum 12” Duct)

Standard 90° Installation

(Flat Bracket)

(Fits a minimum 18” Duct)

Patent Pending 45° Installation

(Angled Bracket)

(Fits a minimum 8” Duct)

Patent Pending 45° Installation

(Angled Bracket)

(Fits a minimum 14” Duct)

UV-Aire Configurations

Содержание UV-AIRE UV-E









Отзывы:

Нет отзывов