Field Controls PVG-100 Скачать руководство пользователя страница 10

page 10 of 12

MULTIPLE VENTING SYSTEMS

1.  To vent a 24 VAC controlled boiler or furnace and a 

30 millivolt residential water heater using one PVG 
power venter refer to the following.

a.  Follow the instructions for safe and proper 

venting previously specifi ed in this manual. 
Make sure that the combined gross BTU/HR 
input and equivalent vent pipe length does not 
exceed the maximum venting capacity of the 
venter selected.

b.  A CK-20FV or CK-20FG control kit MUST be 

added to the system to properly control the 
venter during operation of the water heater. 
Refer to Figure 10 and Diagrams C and D for 
vent pipe arrangement and wiring information.

2.  To vent two 24 VAC appliances using one PVG 

power venter refer to the following.

a.  Follow the instructions for safe and 

proper venting previously specifi ed in 
this manual. Make sure that the combined 
gross BTU/HR input and equivalent vent pipe length does not exceed the maximum venting capacity of 
the venter selected.

b.  A CK-41 Control Kit must be added to the system to properly control the venter when common venting an 

additional 24 VAC furnace or boiler. Tee the draft tube on the PVG unit to connect to the air pressure switch 
on the Control Kit. Refer to Diagram D for wiring instructions. 

PV SERIES POWER VENTER: VERTICAL VENTING OPTION

Diagram C illustrates correct and incorrect installation of PV series venter in vertical vent confi guration (except 
PVE-1200). The correct installation maintains the required vertical position of the pressure switch; the incorrect 
installation does not. The following conditions must also be observed:

• 

Natural gas, LP gas or #2 fuel oil appliance rated at 75% or greater non-condensing type of appliance

• 

Maximum input temperature at power venter:  575°F

Figure 10

REPLACEMENT PARTS LIST
The following items are available for replacement, if necessary.

REPLACEMENT PARTS LIST

DESCRIPTION

PVG-100

PVG-300

PVG-600

Motor

46032000

46032000

46083300

Blower Wheel

46080100

46033400

46089400

24 VAC Relay

46282800

46282800

46282800

Pressure Switch

602602001

602602002

602602003

P/N 46246300 Rev M 04/20

Содержание PVG-100













Отзывы: