Fibocom L860-GL Скачать руководство пользователя

Страница: 65 / 254

FIBOCOM L860 AT Commands User Manual

Page 65 of 254

Command

Description

+CCLK (list of supported <time>s)

Parameters

<time> ASCII string of format:

yy/MM/dd,hh: mm: ss±zz

yy/MM/dd,hh: mm: ss

yy/MM/dd,hh: mm

yy - 2-digit year [2000-2069]

MM - 2-digit month [01-12]

dd - 2-digit day of month [00-31]

hh - 2-digit hour [00-23]

mm - 2-digit minute [00-59]

ss - 2-digit seconds [00-59]

zz - (optional) time zone offset from GMT, in quarter-hours [-47...+48]. If this value is

not specified, the time zone offset will be 0.

Example

AT+CCLK=?

AT+CCLK="01/01/01,01:01:01-08"

AT+CCLK?

+CCLK: "01/01/01,01:01:01-08"

Reference

3GPP TS 27.007

5.1.2 +CTZU, Automatic Time Zone Update

This command enables/disables (on/off) the automatic update of the time zone via NITZ.

Command

Description

Set

[Function]

Execution command enables/disables the automatic update of the time zone.

[Syntax]

AT+CTZU=<on off>

Содержание L860-GL































































































































































































































































Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды

Fibocom L860-GL, Руководство пользователя по командам

Результаты поиска

Содержание L860-GL

Отзывы:

Похожие инструкции для L860-GL

Бренды по названию

Популярные бренды