Fibocom L610 MiniPCIe Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 59

Fibocom L610 MiniPCIe Series Скачать руководство пользователя страница 33

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved

FIBOCOM L610 Series Hardware Guide

Page 33 of 59

1. When the module is working properly, do not cut off the power of the module immediately to avoid

damaging the internal Flash. It is strongly recommended to shut down the module by PWRKEY or AT

command before cutting off the power supply.

2. The AT command to shut down, not suit for auto power-on.

3.3.2.1 Shutdown Timing

Figure 3-7 Shutdown timing control diagram

3.3.3 Module Reset

L610 modules can be reset by hardware and AT command.

Reset Mode

Reset Method

Hardware

Pull down RESET_N for Tst (100ms) and then pull up the level

AT command

AT+CFUN=15

The AT command reset is not applicable in cases where the application circuit is

automatically started

3.3.3.1 Reset Circuit

The reset reference circuit is shown in Figure 3-6. It is similar to the PWRKEY control circuit. The client

can control the RESET_N pin using an OC/OD drive circuit or button.

«
...
31
32
33
34
35
...
»

Содержание L610 MiniPCIe Series




























































Отзывы:

Нет отзывов