manualshive.com logo in svg

FIBARO FGBHCD-001, Руководство по эксплуатации

Поделиться
Скачать
FIBARO FGBHCD-001 Скачать руководство пользователя страница 5

5

PAIRING THE  ACCESSORY

#3: Pairing the  accessory

1.  Open the Settings app on your iOS device.
2.  Go to the 

Bluetooth

® section, and turn the 

Bluetooth

® on.

3.  Place the accessory next to your iOS device.
4.  Open a HomeKit compatible app of your choosing on your iOS 

device.

5.  Open pairing window in your HomeKit app to detect available  

accessories.

6.  Choose CO Sensor you wish to pair.
7.  You can identify it - CO Sensor will blink green.
8.  Find HomeKit Setup Code on the last page of 

Quick Start Guide

  

included in the box that looks like this:

9.  Start pairing with your HomeKit app.
10. Point your iOS device’s camera at the Setup Code to scan it or en-

ter the Setup Code manually.

11. If entered Setup Code is valid, the device will complete the setup 

process.

12. Follow instructions displayed in the application.

XXX-XX-XXX

NOTE

Remember to keep 

your HomeKit Setup 

Code in safe place. You  

may need it in case of 

re-pairing.

i

Содержание FGBHCD-001













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды