FIAP profiwork Fischauswaschbürste
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
5
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
www.fiap.com
GB
Notes on these instructions
Before first use, please read the operating instructions and familiarize yourself with the device.
Observe the safety instructions for the proper and safe use.
Intended Use
The FIAP profiwork Fish Cleaning Brush Machine, hereinafter referred to as device has been
manufactured exclusively for use in aquaculture and use at an operating voltage of 380-400 volts.
The device is suitable for use in compliance with the national installation regulations.
Improper use
Improper use can lead to dangers of people handling this device. By improper use, our liability as well
as the general operating license expires.
CE Declaration
In accordance with the EC Directive EMC Directive (2004/108/EC) and the Low Voltage Directive
(2006/95/EC), conform. The following harmonized standards were applied:
EN 55014-1, EN 55014-2, EN 60335-1, EN 60335-2-41, EN 60598-1, EN 60598-2-18, EN 61000-3-2,
EN 61000-3-3, EN 61558 -2-6, EN 60598-2-7, EN 61558-1, EN 60825-1
Safety
For safety reasons children under 16 or people who can not recognize the potential hazards of this
appliance or are not familiar with these instructions, are not allowed to use this product!
Please keep these operating instructions in a safe place! When changing owners pass on the
instructions. All work with this appliance may only be carried out in accordance with these instructions.
By improper use or no correct installation the combination of water and electricity can lead to serious
danger to life and limb. Operate the unit only if no persons are in the water! Before reaching into the
water, always disconnect the power supply to all devices in the water. Compare the electrical data of
the power supply to the label on the packaging or on the device. Make sure that the unit is secured by
a residual current device with a rated residual current of maximum 30 mA safe. Operate the unit only
on a correctly fitted socket. Keep the power plug and all connection points dry! Lay the connection
cable protected so that damage is excluded. Only use cables, installations, adapters, extension or
connection cables with earthed that are approved for outdoor use. Do not carry or pull the unit by the
cable! With a defective cable or enclosure, the unit must not be operated! If the power cord of the
appliance is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a
hazard. When the cable is damaged, the appliance should be discarded. Electrical installations must
comply with international and national installation requirements. Never open the housing of the device
or its associated parts, unless specifically noted in the instructions. Do not make any technical changes
on the device. Use only original spare parts and accessories. Only be carried out by authorized service
centers repairs. It must be ensured that all conductive parts (screws, terminals, etc.) are isolated and
can not be touched directly! For questions or problems, please contact for your own safety to a
qualified electrician.
SAFETY:
Please read completely before using the instructions carefully. It contains important
information for correct operation.
FIAP profiwork Fischauswaschbürste
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
6
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
www.fiap.com
Electrical connection
The electrical connection must be carried out according to the VDE and EVU by an authorized
specialist. All performance data can be found on the nameplate. All work on the unit are carried out in
de-energized condition!
Installation and commissioning
See also the instruction video on our YouTube channel
http://www.youtube.com/user/FIAPGmbH
.
Facilitate the power supply and the FIAP profiwork Fish Cleaning Brush Machine is ready for use.
C
ommissioning
1. Turn on the FIAP profiwork Fish Cleaning Brush Machine.
2. Gently press the gutted fish against the fish cleaning brush. Slide the gutted fish on the brush back
and forth until the fish is clean.
3. After use, clean the fish cleaning brush with warm water.
Cleaning and maintenance
Caution! Before cleaning or maintenance, always remove the power plug!
After use, clean the FIAP profiwork Fish Cleaning Brush Machine with warm water. The machine and
its components are not with solvents, flammable or toxic cleaning liquids. Make sure that the plug has
been pulled out of the socket.
Disposal
The device must be disposed of according to national regulations.
Ask your dealer.
