Fetco CBS-2041e Скачать руководство пользователя страница 2

 

Contact Information 

 

FETCO 

Food Equipment Technologies Company 
640 Heathrow Drive 
Lincolnshire 

 IL 

 60069 

 USA 

 

Internet: 

www.fetco.com 

Phone:

 (800) 338-2699 (US & Canada) 

             (847) 719-3000 

     Fax:

 (847) 821-1178 

 

Emergency Service Only:

 (800) 660-0035 (U.S. & Canada) 

 

Email:

 [email protected] 

           [email protected] 

 

Description & Features 

 
The CBS-2041 and CBS-2042 feature our patented intermittent spray over technology, which works like this: 
 
The following variables are programmed for each batch size: 
 

 

Brew volume 

 

Prewet percent (Percentage of the brew volume) 

 

 

 

Brew time 

 

Prewet delay (The time between prewetting and the brew cycle.) 

 

 

 

Bypass percent 

    (Percentage of the brew volume) 

 

Drip delay (The time between the end of the brew cycle 

     and the unlocking of the brew basket.) 

 
Using these variables, the software calculates how much water to use for prewetting, bypass, and brewing.  The 
total brew time is divided into several 30 second cycles. Within these cycles, the software calculates how long to 
spray water over the coffee grounds, and how long to pause before the next cycle begins.  The bypass valve opens 
at the beginning of the brew cycle and dispenses the correct amount of water all at once. 
 

Features 

 

 

Two fully programmable batch sizes per side 

 

Magnetic brew basket sensor 

 

Adjustable prewetting cycle 

 

Brew basket safety locks 

 

Adjustable bypass 

 

Brew temperature protection 

 

Electronically controlled hot water service 

 

 

Specifications 

Requirements 

 

Water Requirements:

 

 

Electrical: 

See electrical configuration chart.

 

            CBS-2041: 20-75 psig, 1 gpm 

 

            CBS-2042: 20-75 psig, 1 ½ gpm

 

 

Coffee Filters:

 

13” X 5 ”  FETCO Product # F002

 

 

Содержание CBS-2041e



















Отзывы: