background image

EHMB

Festo – EHMB – 2019-05c English

13

 Check whether the proximity sensors operate as desired.

 Correct the position of the cams if necessary (

è

 5.4 Electrical installation).

Note

The lubrication intervals depend on the product load.

 Shorten the lubrication intervals to half the length in case of:

Speed 

 1 m/s

Load factor 

 80 %

Ambient temperature close to +40 °C

Frequent acceleration and braking

Dusty and dirty environment.

To optimise the service life of the toothed belt with swivel angles less than 360°:

1. Perform the following steps after every 2 million load changes:

Dismantle the payload and rotate by 90°.

Mount the payload again.

Also move the trip cams by 90° in the same direction (

è

 Fig. 9 in chapter 5.4 Electrical installation).

A different part of the toothed belt then comes into the load zone of the gears.

2. Repeat commissioning.

8

Disassembly and repair

WARNING

Unexpected movement of components.

Injury due to impacts or pinching.

 When working on the product, switch off the control and secure it to prevent it from

being switched back on accidentally.

Note

The reference position is lost when the motor, trip cam or electric cylinder is dismantled.

 Start homing as detailed in chapter 6  Commissioning in order to determine the new

reference position.

If repairs are required:

 Send axis to Festo or contact your local Festo service centre (

è

 www.festo.com).

Festo carries out the required repairs, fine adjustments and checks.

 Information about spare parts and auxiliary means (

è

 www.festo.com/spareparts).

Содержание EHMB Series





















Отзывы: