Assembly instructions (Original: de)
8048288
1509NH
†‡
Adjusting kit
EADC-E15-...-E7
Festo AG & Co. KG
Postfach
73726 Esslingen
Germany
+49 711 347-0
www.festo.com
1.
Parts list
21750d_1
1
Adjusting
plate
2
Slot
nut
3
Screw
1)
4
Washer
5
Square
nut
6
Adjusting
bolt
7
Screw
8
Washer
2)
(1x)
(4x)
(2x)
(2x)
(2x)
(2x)
(4x)
(4x)
19406d_16
Not in scope of delivery:
9
X-module
EHMX
2.
Intended use
Adjusting kit EADC-E15-...-E7: Adjustable mounting of the X-module
9
or
handling system YXCF/YXCR.
3.
Safety instructions and notes on mounting
Switch off power supply and compressed air before mounting work.
Observe the safety instructions (
applicable documents).
Comply with tightening torques (
table).
Information
Applicable documents
Description of the handling system YXCF/YXCR
Accessories of the handling system YXCF/YXCR
www.festo.com/catalogue
4.
Screw sizes and tightening torques M
A
3)
EHMX-EGC- 50
80
120
185
7
Screw
M3 x 16 M5 x 25 M6 x 30
M
A
[Nm]
1.2
5.9
9.9
3
Screw
1)
M5 x 30 M8 x 40
M
A
[Nm]
5.9
34
m
[mm]
≥
12
≥
15
h
[mm]
7 ± 2
8 ± 3
Max. height compensator
[mm]
4
6
Y2
[mm]
62 104 140 209
21750d_9
Observe sufficient screw-in
depth m of the screws
3
.
1)
The screw
3
and its tightening torque M
A
as well as the screw-in depth m are designed for
mounting on steel.
2)
The washers
8
are necessary only for size 50.
3)
Tolerance for tightening torques M
A
without indication of tolerance ± 20 %
5.
Mounting
21750d_2
Screw adjusting bolts
6
flush into the square
nuts
5
.
21750d_3
Push square nuts
5
into
the adjusting plate
1
.
21750d_4
Place slot nuts
2
in the
slots.
Place washers
8
(if availa-
ble) under the screws
7
.
Clamp the adjusting
plate
1
to the X-module
9
with the screws
7
.
19406d_12
Comply with number n and
support spacings X2
(
applicable documents).
21750d_5
Position adjusting plate
1
.
Tighten screws
7
.
21750d_6
Place washers
4
under-
neath the screws
3
.
Place screws
3
in the mid-
dle of the elongated hole.
Lightly clamp the adjusting
plate
1
to the mounting
surface with the screws
3
.
19344d_9
Use spanner with t
.
5 mm.
If t
,
5 mm, the maximum
height compensator is smaller
by the difference (t
−
5) mm.
21750d_7
Align X-axes exactly with
each other (
applicable
documents).
Screw adjusting bolts
6
in
or out (maximum height
compensator
table).
21750d_8
Apply counter pressure to
the adjusting bolts
6
.
Tighten screws
3
.
Check:
–
The adjusting bolts
6
have
not twisted.
–
The alignment has been
maintained.
2
5
4
3
1
7
5
6
1
5
9
7
3
4
1
6
1
2
7
6
8
9
8
3
6
