Festo DNCKE Скачать руководство пользователя страница 22

Страница: 22 / 26

DNCKE/KEC

Festo – DNCKE/KEC – 2017-10b English

Maintenance and care

WARNING

Unexpected movement of components.

Injury due to impact or pinching.

When working on the clamping unit, switch off the control and secure it against be

ing switched back on unintentionally.

Clean the clamping unit as required using a soft cloth. Do not use aggressive cleaning agents.

The clamping unit is lubricated for life. Additional lubrication is not necessary.

Disassembly and repair

WARNING

Unexpected movement of components.

Injury due to impact or pinching.

Secure payload and verify load-free status before dismounting.

Exhaust the clamping unit before working on it.

Observe instructions on transport (

4 Transport).

WARNING

Flying parts!

Injury due to impact or pinching.

Loaded springs may be released suddenly during dismantling. The sudden release of

internal spring forces (e.g. when dismantling the housing cover) poses a risk of injury.

Do not disassemble clamping unit.

If repairs are required:

Send clamping unit to Festo or contact Festo service (

www.festo.com).

Information about spare parts and auxiliary tools (

www.festo.com/spareparts).

Disposal

Dispose of the clamping unit and its packaging at the end of its lifecycle by using environmentally

friendly ways of recycling in accordance with applicable specifications.

Accessories

www.festo.com/catalogue

Содержание DNCKE



























Результаты поиска

Содержание DNCKE

Отзывы:

Бренды по названию

Популярные бренды

Festo DNCKE, Руководство по эксплуатации

Результаты поиска

Содержание DNCKE

Отзывы:

Бренды по названию

Популярные бренды