Festo CPX-E Series Скачать руководство пользователя страница 26

Страница: 26 / 28

Terminology

Festo – CPX-E-PB-EN – 2017-07 – English

Terminology

Term/abbreviation

Description

Bus module

Connects system CPX-E to the network; transmits control signals to the
connected modules CPX-E and monitors their functionality.

Device description file

Protocol-specific file for configuring the bus module in the control software for
the higher-order controller. This contains all the information required to
parameterise the system CPX-E via control software.

DIL switch

Switch consisting of several switch elements with which settings can be made
(dual in-line).

DPV1

PROFIBUS extension for acyclic access to system data during running time.

GSD file

Device description file for PROFIBUS (generic station description)

I/O

Input and output

I/O diagnostic interface

Network-independent diagnostic interface at I/O level, which enables access to
the internal data of the system CPX-E.

I/O module

Collective term for modules that provide analogue or digital inputs and/or
outputs.

Modules CPX-E

Collective term for modules that can be integrated in a system CPX-E.

PLC

Programmable logic controller

Status bits

Internal status information (common diagnostic messages) of the system CPX-E,
provided as input signals via the network.

System CPX-E

Complete system consisting of modules CPX-E.

Tab. B.1

Содержание CPX-E Series





























Результаты поиска

Содержание CPX-E Series

Отзывы:

Похожие инструкции для CPX-E Series

Бренды по названию

Популярные бренды

Festo CPX-E Series, Описание

Результаты поиска

Содержание CPX-E Series

Отзывы:

Похожие инструкции для CPX-E Series

Бренды по названию

Популярные бренды