Festo CPE-10-PRS series Скачать руководство пользователя страница 10

Страница: 10 / 12

CPE...-PRS...

Festo CPE...-PRS 2017-12f English

Eliminating faults

Fault

Possible cause

Remedy

Loss of pressure

Diaphragm at interface of two pres
sure zones broken through

Replace the CPE-..PRS...

Tubing not connected correctly

Reconnect tubing correctly

Air can be heard to
escape

No seals at relevant point

Check seals

Valve slide does not snap into notch

Let valve slide snap into notch (valve
slide and valve must be flush)

Fig. 14

Technical specifications

Type

CPE-10-PRS...

CPE-14-PRS...

CPE-18-PRS...

CPE-24-PRS...

Design

Pneumatic sub-base

Fitting position

As desired

Medium

Compressed air to ISO 8573-1:2010 [7:4:4]
Lubricated operation possible (required during subsequent operation)

Permissible operating
pressure

–0.9 bar ... max. +10 bar

Max. perm. tightening
torque for

cylindrical

connectors

6 Nm

8 Nm

30 Nm

Permissible temperature
range

Ambient, medium:

–5 °C ... +50 °C

Storage:

–20 °C ... +40 °C

Materials

Housing:

Polyamide

Fittings:

Aluminium

Seals: Nitrile

rubber

Connections: Galvanized

steel

Fig. 15

Содержание CPE-10-PRS series













Результаты поиска

Содержание CPE-10-PRS series

Отзывы:

Похожие инструкции для CPE-10-PRS series

Бренды по названию

Популярные бренды

Festo CPE-10-PRS series, Руководство по эксплуатации

Результаты поиска

Содержание CPE-10-PRS series

Отзывы:

Похожие инструкции для CPE-10-PRS series

Бренды по названию

Популярные бренды