Festo 548076 страница 86 Скачать руководство пользователя

Страница: 86 / 92

86 / 92

Festo 7DHTGd_en

4.6

Mounting the energy throughfeed

4.6.1

Mounting of the pneumatic and electrical module

An electrical module is additionally mounted on the pneumatic module of the P4E4 / P4L12 versions.
In the event of a pneumatic module defect, contact the regional Festo contact (



www.festo.com

1. Insert the centring sleeves into the holes in the housing of the pneumatic

module.

2. Push the air pipe assembly through the rotary indexing table.

The air connections of the pneumatic module are on the same side as the air
connections of the rotary indexing table.

3. Carefully position the housing of the pneumatic module on the rotary index-

ing table, at the same time, feed the centring sleeves into the holes in the
rotary indexing table.

4. Screw in socket head screws (4×) and tighten to appropriate tightening

torque.

Size

Tightening torque

DHTG-…-A-P4

2.9 Nm ±20 %

DHTG-…-A-P4E4

2.9 Nm ±20 %

DHTG-…-A-P4L12

2.9 Nm ±20 %

5. Mount rotary distributor



Chapter 4.6.2 on page 86

4.6.2

Mounting the rotary distributor, only DHTG--A-P4 / P4E4 / P4L12

Requirement

The pneumatic and the electrical module are mounted



Chapter 4.6.1 on page 86

DHTG-65 / 90-A-P4 / P4E4 / P4L12

1. If dismantled, screw grub screw into the plate until it stops.

Содержание 548076





























































































Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды

Festo 548076, Инструкции по ремонту

Результаты поиска

Содержание 548076

Отзывы:

Похожие инструкции для 548076

Бренды по названию

Популярные бренды