background image

 

 

overcharge, over-discharge and excessive load amperage, the FnS Power Lithium Batteries 

must always be installed with a charge controller and the appropriate settings to protect the 

FnS Power from open PV voltage and other high voltage charging sources. The FnS Power 

Lithium Battery Management System (BMS) alone will not protect the FnS Power  Lithium 

batteries from these extreme electrical phenomena. Failure to adhere to installation protocol 

will void the Warranty. 

(2) FnS Power’s products are designed to meet stated U.S. safety standards and regulations. 

Because  local  safety  standards  and  regulations  vary  significantly,  FnS  Power  cannot 

guarantee that products  meet all applicable requirements in each locality. Buyer assumes 

responsibility for compliance with such safety standards and regulations in the localities in 

which a product will be shipped, sold or used. Before purchase and use of any product, Buyer 

shall review the product application, and national and local codes and regulations, and must 

verify that the use and installation of the product will be in compliance therewith. 

(3)  Only  use  a  FnS  Power  approved  LFP  charger  if  ancillary  charging  is  required  before 

installation, testing, or troubleshooting. Failure to use  a FnS Power approved LFP charger 

will damage the battery and void the warranty. 

(4)  Improper  sizing  and/or  charge  parameters  can  cause  the  battery  to  malfunction.  It  is 

necessary to both correctly size a system and enter the correct charge parameters into your 

charge controller and/or inverter. Please see Product Instructions for these topics. Failure to 

check these may result in a dysfunctional system.  

(5) If there is any inconsistency between this Limited Warranty and any other agreement or 

statement included with or relating to FnS Power Product or services, this Limited Warranty 

shall govern. If any provision of this Limited Warranty is found invalid or unenforceable, it 

shall be deemed modified to the minimum extent necessary to make it enforceable and the 

remainder of this Limited Warranty shall remain valid and enforceable according with its terms. 

(6) Our goods come with guarantees that cannot be excluded under the Australian Consumer 

Law. You are entitled to a replacement or refund for a major failure and compensation for any 

other  reasonably  foreseeable  loss  or  damage.  You  are  also  entitled  to  have  the  goods 

Содержание SSIF2P15S48100C

























































Отзывы: