Ferm TW-820, Инструкции

Страница: 3 / 4

6 Ferm
Extension cables
Use only three core earthed extension cables suitable
for the power input of the tool (minimum cable size
1.5mm
2 ). Plug into an earthed socket only.
When using a cable reel unwind it fully. Do not use long
extension cables.
Outdoors use
If the tool is suitable to be used outdoors, only use an
extension cable intended for outdoor use and marked
accordingly. Use a RCD (residual current device) to pro-
vide protection against electrical shock. Do not use in
rain or damp conditions.
Connect a dust extraction device
Whenever there are facilities for fitting a dust or fume
extraction system, make sure it is connected and used.
Use recommended accessories
The use of any other accessory or attachment other than
recommended in the instructions or catalogue may pre-
sent a risk of personal injury. Use an extension cable with
a minimum conductor size of 1.5mm
2 .
When using a cable reel unwind it fully.
INSTALLATION
For easy assembly please follow the steps described
below. It is recommended not to fully tighten the screws.
Leave this operation to the end.
1. Fix the right leg (A) (without front holes) below
board (B) using 3 screws.
2. Fix the support (C) (groove to the inside) to the big
leg (A), using 2 long bolts per support.
3. Insert the plywood board (D) into the inner grooves
of the support.
4. Fix the left leg (A) (with front holes) below the board
(B), using 3 screws, and the support (C) using 2 long
bolts per support.
5. Fix the rails (E and G) of the drawer using 2 screws
per rail. (make sure that the wheel is on the inside and
front side).
6. Fix the drawer after the rails have been fixed.
7. Install the clamp by inserting the clamping pegs into
the holes provided. Ensure correct positioning by
pressing it against the board.
8. Complete the assembling by fully tightening all
screws.
A set of wooden clamping pegs is also supplied to insert
into the holes in the clamp and workbench in order to
hold the different pieces to be worked on.
GUARANTEE PROVISIONS
1. Ferm guarantees all material and construction
defects for a period of 36 MONTHS after purchase.
Other claims in respect of damage, of whatever
nature, direct or indirect, to persons and/or mate-
rials are excluded.
2. Always consult your Ferm dealer in the first instance.
Usually he will be able to solve the problem or repair
the defect.
3. If parts are repaired or replaced within the warranty
period, this does not extend the warranty period.
4. Fair wear and tear is not covered by this warranty.
For example motors, switches or bulbs.
5. THIS WARRANTY APLIES ONLY:
•
If you can submit proof of the date of purchase, i.e. a
RECEIPT stating the date of purchase.
• If you have completed and signed the enclosed war-
ranty card. You will find the warranty card in the back
of this manual.
• If no repairs or alterations have been made to the
machine by third parties, nor other than the original
parts have been fitted.
• If the machine was used in accordance with the
instructions.
• If we cannot plead force majeure.
6. The warranty provisions apply in combination with
our terms of delivery and sale.
7. All cost of transport of the product to be repaired are
at buyer’s expense. Badly packed articles are not
accepted.
FERM’S AFTER SALES SERVICE
Save the original packing. Should you ever have to move
the machine there is less risk of damage in the original
packing. In the case of a guarantee claim the product can
be returned best in the original packing.
ENVIRONMENTAL PROTECTION
Recycling raw materials is prefered to dumping them as
waste! To prevent the machine from being damaged
during transport its packing must be strong. Insofar as
possible the packing consists of recyclable materials such
as paper, cardboard and wood.
Ferm 3