Ferm HDM1028, Оригинальное руководство пользователя

Страница: 6 / 100

6
EN
Description
The numbers in the text refer to the diagrams on
pages 2-3
Fig. A
1. On/off switch
2. Drill selection switch
3. Hammer selection lever
4. Chuck
5. Locking sleeve
6. Main grip
7. Auxiliary grip
8. Carbon brush cover
9. Lubrication point
3. ASSEMblY
Before assembly, always switch off the
machine and remove the mains plug
from the mains.
Mounting and removing the accessory
Fig. B
Do not use blunt drill bits or chisels.
Immediately sharpen or replace blunt
drill bits or chisels.
Mounting
• Apply a few drops of oil to the shaft of the
accessory.
• Slide the locking sleeve (5) to the rear.
• Insert the accessory into the chuck (4).
• Secure the accessory by turning it
counterclockwise until it locks into place.
• Release the locking sleeve (5).
Removing
• Slide the locking sleeve (5) to the rear.
• Remove the accessory from the chuck (4).
• Release the locking sleeve (5).
Mounting and removing the auxiliary grip
Fig. C
Mounting
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Mount the auxiliary grip (7) by sliding it over the
chuck (4).
• Turn the auxiliary grip (7) to the required
position.
• Tighten the auxiliary grip (7) by turning it
clockwise.
Removing
• Loosen the auxiliary grip (7) by turning it
counterclockwise.
• Remove the auxiliary grip (7).
• Tighten the auxiliary grip (7) by turning it
clockwise.
Mounting and removing the dust collector
Fig. D
The dust collector prevents dust from entering the
machine when drilling into ceilings.
Immediately replace a damaged dust
collector.
Mounting
• If necessary, remove the accessory from the
chuck (4).
• Slide the dust collector (15) over the shaft of
the accessory.
• Insert the accessory with the dust collector
(15) into the chuck (4).
Removing
• Remove the accessory with the dust collector
(15) from the chuck (4).
• Remove the dust collector (15) from the
accessory.
4. USE
Switching on and off
Fig. A
• To switch on the machine, press the on/off
switch (1).
• To switch off the machine, release the on/off
switch (1).
Setting the operating mode
Fig. A & E
The drill selection switch and the hammer
selection lever must be set according to the
required operating mode. Refer to the table below
to set the required operating mode.
Setting Operating mode
Fig. E
A Demolition hammer / Chisel
B Hammer drill
C Drill
• Turn the drill selection switch (2) and the
hammer selection lever (3) to the required
position.
Hints for optimum use
• Clamp the workpiece. Use a clamping device
for small workpieces.
• Firmly hold the machine by the grip.
• Set the operating mode.
• Switch on the machine.
• Do not apply too much pressure on the
machine. Let the machine do the work.
• Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
5. ClEANING AND
MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and
dirt. Remove very persistent dirt using a soft
cloth moistened with soapsuds. Do not use any
solvents such as gasoline, alcohol, ammonia
etc. Chemicals such as these will damage the
synthetic components.
Checking and replacing the carbon brushes
Fig. A
The carbon brushes must be checked regularly.
If the carbon brushes are worn, the machine will
start to run unevenly.
Only use the correct type of carbon
brushes.
• Remove the carbon brush holders (8) using a
screwdriver.
HDM1028 Ma 1611-07.indd 6 23/11/16 16:35