Ferm FKS-165L, Руководство пользователя

Страница: 9 / 62

Ferm 09
• Never leave the circular saw unattended.
• Use this circular saw to saw only wood or wood-like products.
Safety tips for the laser beamer
• Never look into the light beam of the laser.
• Never point the light beam of the laser at humans or animals.
• Do not point the light beam of the laser at strongly reflecting material. Hazard from reflected light.
• Only have repairs made to the laser beamer by qualified personnel / professional repair
specialists.
• Do not insert any hard objects into the laser optics.
• Clean the laser optics with a soft, dry brush.
Using the machine
• Use clamps or a vice to hold the work.
• Never remove wood chips and saw dust that is close to the saw blade with your hands. If
there are small pieces of wood left between the fixed and the movable parts, the circular
saw will have to be stopped. The plug needs to be removed from the socket, before any left
piece can be removed.
• Check that the blade is suitable for the spindle speed of the circular saw. Do not attempt to
cut before the circular saw has reached full speed. Make sure the circular saw runs without
load (i.e. is not in contact with the work) when you switch it on. The circular saw must have
reached its full speed first.
• Never cut wood that is thicker than the depth of the saw blade.
• When cutting in wooden walls or floors, check there is no wiring or piping where you intend
to cut.
• Switch off the tool and wait until the blade has stopped completely before moving the saw
away from the work or putting it down. Hearing protection should be worn when using
circular saw.
Switch off the machine immediately when you discover:
•
A defective mains plug or mains lead;
• A defective switch.
• Overheating of the circular saw.
• Smoke or odeur caused by scorched insulation.
Electrical safety
When using electric machines always observe the safety regulations applicable in your coun-
try to reduce the risk of fire, electric shock and personal injury. Read the following safety
instructions and also the enclosed safety instructions. Keep these instructions in a safe place!
Always check that the power supply corresponds to the voltage on the rating
plate.
The machine is double insulated; therefore no earth wire is required.
GB
D
NL
F
E
P
I
S
SF
N
DK
116 Ferm
• Skru det skruer af og fjern omslaget.
• Byt de gamle batterier med nye. De skal bruge 2 x 1.5 V “Mikro/AAA” batterier.
• Smid aldrig gamle batterier ud med køkkenaffaldet, men aflever dem i stedet til et specielt
batteri eller kemikali afleveringsdepot.
• Når De isætter batterierne, sikre Dem at +/- terminalen er korrekt placeret som vist inde i
batterirummet.
• Check at laser lyset er korrekt lukket ved forsigtigt at åbne låget opad. Hvis låget åbner,
skal De gentage lukke proceduren indtil låget forbliver korrekt lukket.
Justering af laser lyset
• Behandling ved transport og ofte brug kan påvirke laser lysets præcision.
• Laser lyset i sig selv kan let blive justeret.
• Hold bladet af den runde sav mod en lige kant eller perfekt lige planke.
• Tænd for laser lyset.
• Check om laser lyset løber parallel med kanten eller plankens kant.
Hvis laser lyset ikke løber parallel, gør da følgende:
•
Løs de skrue foran på laseren et par omdrejninger.
• Hold bladet på rundsaven mod en lige kant eller perfekt lige planke.
• Juster laseren sådan at den løber fuldstændigt lige med kanten.
• Fastskrue de skrue igen.
5. VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når der udføres vedligeholdelse-
sarbejder på mekanikken.
Maskinerne er udviklet til at fungere længe uden problemer med et minimum af vedlige-
holdelse. Ved at rengøre maskinen regelmæssigt og behandle den korrekt, bidrager De til
en længere levetid for maskinen.
Fejl
Hvis rundsaven ikke virker hensigtsmæssigt, kan du gennemgå følgende mulige årsager
og tilhørende løsninger for at afhjælpe problemerne.
UK
D
NL
F
E
P
I
S
SF
N
DK