Ferm
07
Faulty and/or discarded electrical or electronic apparatus have to be collected
at the appropriate recycling locations.
Danger
a)
Keep hands away from cutting area and the blade. Keep your second hand on auxiliary
handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade.
b)
Do not reach underneath the workpiece. The guard cannot protect you from the blade
below the workpiece.
c)
Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
d)
Never hold piece being cut in your hands or across your leg. Secure the workpiece to a
stable platform. It is important to support the work properly to minimize body exposure,
blade binding, or loss of control.
e)
Hold power tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also
make exposed metal parts of the power tool "live" and shock the operator.
f)
When ripping always use a rip fence or straight edge guide. This improves the accuracy of
cut and reduces the chance of blade binding.
g)
Always use blades with correct size and shape (diamond versus round) of arbour holes.
Blades that do not match the mounting hardware of the saw will run eccentrically, causing
loss of control.
h)
Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were
specially designed for your saw, for optimum performance and safety of operation.
Causes and operator prevention of kickback
•
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing
an uncontrolled saw to lift up and out of the workpiece toward the operator;
•
When the blade is pinched or bound tightly by the kerf closing down, the blade stalls
and the motor reaction drives the unit rapidly back toward the operator;
•
If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of
the blade can dig into the top surface of the wood causing the blade to climb out of
the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions
and can be avoided by taking proper precautions as given below.
a)
Maintain a firm grip with both hands on the saw and position your arms to resist kickback
forces. Position your body to either side of the blade, but not in line with the blade. Kickback
could cause the saw to jump backwards, but kickback forces can be controlled by the
operator, if proper precautions are taken.
b)
When blade is binding, or when interrupting a cut for any reason, release the trigger and hold
the saw motionless in the material until the blade comes to a complete stop. Never attempt to
remove the saw from the work or pull the saw backward while the blade is in motion or kickback
may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
c)
When restarting a saw in the workpiece, centre the saw blade in the kerf and check that
saw teeth are not engaged into the material. If saw blade is binding, it may walk up or
kickback from the workpiece as the saw is restarted.
GB
D
NL
F
E
P
I
S
SF
N
DK
118
Ferm
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er
så vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres
på en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for garantibetingelserne.
CE
KONFORMITETSERKLÆRING (DK)
Vi erklærer herved, udelukkende på eget ansvar, at dette
FKS-185L
opfylder følgende standarder eller standardiserede dokumenter:
EN60745-1, EN60745-2-5, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3, EN60825-1
i henhold til bestemmelserne i direktiverne:
98/37/EC, 2006/95/EC, 89/336/EEC, 2002/95/EC, 2002/96/EC
01-08-2007
ZWOLLE NL
J.A. Bakker - van Ingen
J. Lodewijk
CEO Ferm BV
Quality Manager Ferm Global
Det er vores hensigt til stadighed at forbedre vores produkter, og vi forbeholder os derfor
til enhver tid retten til at ændre produktspecifikationerne uden forudgående varsel.
Ferm BV • Lingenstraat 6 • 8028 PM Zwolle • Holland
UK
D
NL
F
E
P
I
S
SF
N
DK
Содержание FKS-165L
Страница 2: ...Ferm 123 02 Ferm Fig A Explodedview ...
Страница 4: ...Ferm 121 UK D NL F E P I S SF N DK 04 Ferm Fig E ...
