background image

40

•  Never  put  sideward  pressure  on  the  blade. 

This may cause the blade to break.

•  Be  careful  when  cutting  wood  with  knots, 

nails or cracks in it and/or dirt on it, as these 

can cause the blade to get stuck.

•  Never leave the circular saw unattended.

5.6 Safety tips for the laser beamer

•  Never look into the light beam of the laser.

•  Never  point  the  light  beam  of  the  laser  at 

humans or animals.

•  Do  not  point  the  light  beam  of  the  laser  at 

strongly reflecting material. Hazard from 

reflected light.

•  Only have repairs made to the laser beamer 

by qualified personnel / professional repair 

specialists.

•  Do not insert any hard objects into the laser 

optics.

•  Clean the laser optics with a soft, dry brush.

5.7 Using the machine

•  Use clamps or a vice to hold the work.

•  Never remove wood chips and saw dust that 

is close to the saw blade with your hands. If 

there are small pieces of wood left between 

the fixed and the movable parts, the circular 

saw will have to be stopped. The plug needs 

to be removed from the socket, before any 

left piece can be removed.

•  Check that the blade is suitable for the spind

-

le speed of the circular saw. Do not attempt 

to cut before the circular saw has reached full 

speed. Make sure the circular saw runs wit-

hout load (i.e. is not in contact with the work) 

when you switch it on. The circular saw must 

have reached its full speed first.

•  Never cut wood that is thicker than the depth 

of the saw blade.

•  When  cutting  in  wooden  walls  or  floors, 

check if there is no wiring or piping where 

you intend to cut.

•  Switch off the tool and wait until the blade 

has stopped completely before moving the 

saw away from the work or putting it down. 

Hearing protection should be worn when 

using the circular saw.

5.8 Switch off the machine immediately 

when you discover

•  A defective mains plug or mains lead.

•  A defective switch.

•  Overheating of the circular saw.

•  Smoke or odeur caused by scorched insula

-

tion.

6.  ASSEMBLY AND ADJUSTING 

INSTRUCTIONS

Before adjusting the saw, make sure

the plug is removed from the socket.

6.1 Setting the sawing angle (bevel)

  (Fig. 1)

•  Loosen both knobs (11).

•  Rotate  the  soleplate  to  the  correct  position 

(0° - 45°), and tighten the knobs. The sawing 

angle (bevel) can be read on the protractor.

6.2 Fitting the rip fence (Fig. 1)

•  Loosen knob (12).

•  Insert  the  rip  fence  into  the  slots  provided 

(10).

•  Set the correct cut width and tighten the knob 

(12).

6.3 Setting the cut depth (Fig. 1)

•  Loosen knob.

•  Move the soleplate (7) downwards.

•  The cut depth of the saw blade can be read off 

on the side of the safety guard.

•  Tighten the clamping knob once the correct 

depth is set.

6.4 Exchanging or cleaning the saw 

blade (Fig. 1)

•  Use  the  shaft  locking  knob  to  prevent  the 

shaft from rotating.

•  Next loosen the hexagon screw (6) in the centre 

of the saw blade, using the Allen keyprovided.

Содержание BCS-1400












Отзывы: