Ferax BCM-1350 Скачать руководство пользователя страница 4

23

The ON/OFF switch

•  To switch on the tool, press and hold the on/

off switch (1).

•  If you release the on/off switch, the tool will 

be switched off.

7.  ELECTRONIC MOTOR 

CONTROL

7.1 Starting current limiting

The electronically controlled smooth start takes 

care that the machine starts without jerk. In this 

manner, the splashing of thin liquid materials 

is prevent at the same time when switching on 

the machine.

As a result of the machine’s reduced starting 

current, a 16 A fuse is sufficient.

7.2 No load speed reduction

The electronic control reduces the no-load 

speed of the machine which results in reduced 

noise and wear of motor and gear.

7.3 Speed pre-selection

With  the  speed  control  (2)  the  speed  can  be 

continuously pre-selected: the necessary speed 

is dependent on the type of material to be 

mixed. It is recommended that it be confirmed 

with a practical trial.

7.4 Constant electronics

The constant electronics keeps the speed bet-

ween no-load and load nearly constant and 

ensures uniform mixing of the materials.

7.5 Electronic overload protection

In case that the machine is extremely overloa-

ded, an electronic overload protection protects 

the motor from damage. In this case, the motor 

stops and restarts only after the feeding pres-

sure is reduced.

7.6 Temperature-dependant  overload 

protection

To protect the motor from overheating at 

extreme permanent load, it is switched off by 

the protective electronic system when a critical 

temperature is reached.

After a cooling-down period of approx. 3 - 5 

min., de machine is again ready for use and can 

be fully loaded.

When the machine is warmed by use, the tem-

perature-dependent overload protection reacts 

earlier as a result.

8. SERVICE & MAINTENANCE

8.1 Maintenance

Make sure that the plug is removed 

from the mains when carrying out 

maintenance work on the motor.

The machines have been designed to operate 

over a long period of time with a minimum of 

maintenance. Continuous satisfactory opera-

tion depends upon proper machine care and 

regular cleaning.

•  The  ventilating  slots  on  the  motor  casing 

should be cleaned out from time to time.

•  When  the  carbon  brushes  are  worn  out,  the 

machine switches itself off. The machine 

must then be sent to customer service for 

maintenance.

•  After 100 hours: check carbon brushes

•  After 200 hours: renew the grease filling in 

the gearbox

To verify the protective insulation 

remains intact, the machine must be 

subjected to a technical safety test 

afterwards. For this reason, this main-

tenance must be performed exclusi-

vely by a professional electro-work-

shop.

Содержание BCM-1350









Отзывы: