APPLYING POWER
The 30W Siren should be supplied with a solid +12V
voltage and GND from the vehicle using appropriate
installation methods.
The wiring should go directly from the siren to a fuse at the
battery. The fuse and wiring should be sized and installed
such that resistance and voltage drop are minimized.
PROGRAMMING
Excessive resistance and voltage drop can cause low
performance or increased heat in power routing.
MODE 1/MODE 2 OPERATION
Mode 2 takes priority over Mode 1, and will interrupt any
tone currently playing on Mode1. Each mode can be
programmed to operate in either Hands Free or On/Off
operation. To toggle the operation style of a Mode:
1. Power the unit off.
2. Connect the desired Mode and the Tone Select wires to
+12V.
3. Toggle between On/Off Activation and Hands-Free
Activation. Apply power to the unit. A tone may start
playing and after 4 seconds an audible indicator will be
heard that verifies the operation style has been toggled.
•
On/Off Activation:
The Mode will play its
programmed tone while +12V is applied and stop
when it is removed.
To program a Mode in On/Off Operaton, activate
that Mode and use the Tone Select wire (
Blue) to
scroll through the list of tones. The tone that is left
selected will remain that Mode's tone the next time it is
activated.
•
Hands Free Activation:
Each mode can have
a 3 tone list programmed. That mode will play its
first programmed tone as soon as +12V is applied
(including a single tap), and stop when +12V is rapidly
double tapped. If a tone is already playing and the
Mode wire is single tapped to +12V, the next tone in
the 3 tone list will play.
To program a Mode in Hands Free Operation, activate
the Mode, scroll through the 3 tone list and use the
Tone Select wire to set the desired tones for each
position.
P
ARK KILL - OPERATION
When connected to a +12V, the microphone and all tones
(including voice commands and audio files) are muted.
1) Wail
16) 'Move out of the way'
2) Yelp
17) 'Pull over'
3) Fast Yelp
18) 'Step out of the vehicle'
4) Phaser
19) 'Step out with your hands up'
5) Horn
20) 'Remain in your vehicle'
6) Mechanical
21) 'Remain...with the windows down'
7) Manual Wail
22) Test Tone
8) Hi/Lo
23) Italian Police (Policia Vibrato)
9) PCall
24) Italian Ambulance
10) PCall Fast
25) Gendarmerie
11) Horn & Phaser 26) Pompiers
12) Horn & Yelp
27) UMH
13) Phaser & Yelp
28) Police
14) Ecto Siren
29) ASA
15) Bad Boys
30) National Anthem
COLOR
FUNCTION
POLARITY CONNECTION
Black
Ground
12v (-)
Chasis Ground
Red
Battery
12v (+)
Positive Battery Terminal
Brown
Mode 2
12v (+)
Latching Switch
Yellow
Mode 1
12v (+)
Latching Switch
White
Park-Kill
12v (+)
Momentary Signal
Blue
Tone Select
12v (+)
Latching Switch
Green Microphone Input
N/A
Optional Microphone
Gray
Microphone Input
N/A
Mic GBD Input
*Should connect to the barrel of mic jack
WIRING DIAGRAM
SIREN TONES
TONE SELECT
- OPERATION
With one of the Modes selected and a tone playing,
tap the Blue wire to +12V for 1 second to advance the
current tone to the next. Continue to repeat the tone scroll
until the desired tone is selected. That tone will now be
programmed to the selected Mode (Modes will remain
programmed even if power is removed from the unit).
FENIEX
//
2019
// INSTRUCTION MANUAL // v1.4
WEB
//
www.feniexindustries.com
5
TM
