Fender TONE MASTER 59 Bassman, Руководство пользователя, Страница: 3 / 12

REAR PANEL
M. OUTPUT POWER: Selector switch offers full power (45 watts) and
five other attenuated wattage settings (22W, 12W, 5W, 1W, 0.5W)
that tailor room/venue overall loudness to the main speakers. Set
control panel channel volume to personal preference for tube-
emulated response, then set OUTPUT POWER to preferred level.
N. VINTAGE/TIGHT SWITCH: Selects negative feedback of virtual
power amp. VINTAGE is accurate to the ’59 Bassman tube circuit;
TIGHT increases damping of the virtual power amp for tighter
low-end response.
O. CABINET SIM SWITCH: Selects the impulse response when using
XLR BALANCED LINE OUTPUT (R). Switch offers three different
impulse response options. Additional information available at
https://support.fender.com.
P. BALANCED LINE OUTPUT LEVEL: Adjusts output from mic to
line level to XLR BALANCED LINE OUTPUT (R) for external devices
and systems (i.e., PA and recording equipment). When set to “1”,
the maximum level is -5dBu, which may be “hot” for external mic
level inputs; connecting to line input level or activating mic input
pad for lowest noise performance is recommended.
Q. GROUND LIFT SWITCH: Helps eliminate hum or buzz resulting
from connection to improperly grounded equipment when using
XLR BALANCED LINE OUTPUT (R).
R. XLR BALANCED LINE OUTPUT: For balanced connection to
external devices and systems (i.e., PA and recording equipment).
XLR line output remains active when amp is in MUTE mode (B).
S. USB PORT: Connect to a Mac or PC using a USB-C cable to perform
firmware updates.
T. RECOVER/FIRMWARE UPDATE BUTTONS: Upper button is for
use by authorized Fender service personnel only; lower button
activates firmware update mode (when available with instructions
at https://support.fender.com).
U. FOOTSWITCH JACK: Connect included two-button footswitch for
reverb and effect loop bypass here. Note: REVERB (D) and EFFECTS
LOOP (V) default to ON when footswitch is disconnected.
V. EFFECTS LOOP/CLIPPING INDICATOR: Connect external effects
using TRS or standard TS 1/4” instrument cables. Connect amp
SEND to external effect input and amp RETURN to external effect
output. Effects loop can also be turned on and off (bypassed)
using the included two-button footswitch. Clipping indicator LED
illuminates red when effects RETURN is too “hot” and clipping is
occurring. Note that the effects loop is located in the signal path
between the amp and reverb models:
W. IEC POWER INLET (NOT SHOWN): Using the included power
cord, connect to a grounded outlet in accordance with the input
power voltage and frequency specified at the power inlet.
SPECIFICATIONS
TYPE PR 6401
POWER REQUIREMENTS 150 watts (max)
POWER AMP OUTPUT 45 watts into 2Ω (simulated tube amp headroom and dynamics)
INPUT IMPEDANCES Input 1: 1MΩ (both channels) Input 2: 136kΩ (both channels)
EFFECTS LOOP SEND/RETURN Maximum level: +10dBV in/out Nominal level: -10dBV in/out Send: 220Ω (balanced) Return: 10kΩ (balanced)
XLR LINE OUT Maximum level: +24.9dBu Nominal level: +4dBu Impedance: 600Ω (balanced)
SPEAKERS Four 10” Jensen® P10R alnico, 8Ω (PN 0055613000)
FOOTSWITCH Two-button Tone Master (included, PN 9340000173)
COVER Fitted cover (included, PN 0037965000)
DIMENSIONS AND WEIGHT Width: 23.5” (59.7 cm) Height: 22.4” (56.9 cm) Depth: 10.6” (26.9 cm) Weight: 32 lbs. (14.5 kg)
Product specifications subject to change without notice.
EN
GL
ISH
2
For questions and troubleshooting,
contact a Fender specialist at:
1-800-856-9801 (U.S. toll free)
1-480-596-7195 (International)
Additional manual translations available at www.fender.com