background image

MUSTANG

 III/IV/V (V.2)

• Mode 3—

In Mode 3 the footswitch is used to bypass the 

Stompbox, Modulation or Delay effects, using the buttons 

labeled: 

STOMP / MOD / DELAY

 (in line with the MODE  3 

LED). The footswitch button LEDs indicate the effects that are 

active, just like the buttons on the amplifier.

  You can also have a footswitch button assigned to 

bypass the Reverb effect by adding on the 2-button 

Mustang footswitch (see Six-Button Footswitching 

options, below).

• Tuner Mode—

Press and hold the MODE button to activate 

the Tuner. The ampifier screen and the footswitch both will 

display the same tuner information so that you can look in 

either place to tune your guitar. The footswitch will display 

the nearest note; the button LEDs will indicate sharp and 

flat and "in tune" is indicated when the green LED below the 

footswitch display lights up.
Press any footswitch button to exit Tuner mode. 

Two-Button Footswitch (0080997000)

Connect a 2-button footswitch to your Mustang amplifier 

(included with the Mustang III, optional equipment for the 

Mustang IV & V) to enable remote multi-function foot control. 

Use the Utility menus (see page 12) to assign one of the fol-

lowing functions to the 2-button footswitch:

• Select presets (up/down)
• Select Quick Access presets (QA1/QA2)
• Bypass effects (various combinations)
• Set TAP interval

 

Six-Button Footswitching options

Plug both a 4-button and a 2-button footswitch into your 

Mustang amplifier to expand your remote control options. 

By assigning different functions to each footswitch you can 

create more than a dozen different foot control combinations.

 

For example, you could assign Quick Access presets to the 

4-button footswitch and Up/Down presets to the 2-button 

footswitch. Or you could bypass effects with the 4-button 

footswitch and select presets with the 2-button footswitch. 

The choice is up to you.

EXP-1 Expression Pedal

The EXP-1 expression pedal (P/N 2301050000) is a dual-mode 

pedal that can be programmed to control a wide variety of 

parameters on your Mustang amplifier. Plug the EXP-1 pedal  

into the "4 BUTTON FOOTSWITCH" jack .
The EXP-1 operates in two modes, Volume behavior mode 

and Expression behavior mode. Switch between modes by 

pressing down hard on the toe end of the pedal. Red and 

green LEDs on the EXP-1 indicate the current pedal mode:

• Volume

 behavior mode (green) is used to control master 

volume (or the EXP-1 can be set to OFF in Volume mode). 

 

Expression

 behavior mode (red) can be used to control 

most effect and amp parameters on your Mustang amplifier. 

Some common uses are to control the frequency parameter 

of a wah effect or the rate/time parameter of a modulation 

or delay effect. 

  Fender® FUSE™ software can also be used to program 

all settings on your EXP-1 pedal.

EXP-1 Pedal Calibration

The first time you connect the EXP-1 to your Mustang ampli-

fier, you should calibrate it so that the desired range of pedal 

movement registers with the amplifier. Calibration takes less 

than a minute:

To calibrate the EXP-1:

1.

  Plug the EXP-1 pedal into the 4 BUTTON FOOTSWITCH 

jack on the back of your Mustang amplifier using the 

included cable.

2.

  Turn the amplifier OFF.

3.

 Press and hold the UTIL button on the amplifier, then 

turn the amplifier ON. Continue holding the UTIL button 

down until it is no longer illuminated.

4.

  Move the EXP-1 pedal between the desired heel and toe 

endpoints to set the range of pedal movement that is 

registered (recognized) by the amplifier.

10

f e n d e r . c o m

Содержание Mustang Bass














Отзывы: