Fellowes Starlet 2+ 120, Инструкция по эксплуатации

Страница: 2 / 28

A 4
A 5
4
CAPABILITIES
When punching;
- always ensure the machine is on a stable surface
- test punch scrap sheets and set the machine before punching final documents
- remove staples and other metal articles prior to punching
- never exceed the machines quoted performance
- punch front and back covers first
- punch sheets in small batches that do not overload the machine or the user
- lift punch handle to open waste tray, when punch handle is down the waste tray is locked
Punching Capacity
Paper sheets
- 70-80g / 20lb 12 sheets
Transparent covers
- 100-200 micron / 4-8 mil 2 sheets
- 200+ micron / 8+ mil 1 sheet
Other standard covers
- 160-270g / 40-60 lb 2 sheets
- 270+g / 60+ lb 1 sheet
Binding Capacity
Max comb size 16mm comb
Max document (80g / 20lb) 120 sheets
Technical Data
Paper dimensions A4
Punching slots 21 (A4)
Slot pitch 14.28mm / 9/16”
Adjustable edge guide A4 or A5
Waste tray capacity 1000 sheets
Net weight 3.3kg / 7.3lb
Dimensions (HxWxD) 135(390) x 480 x 195mm
5.5”(15.5”) x 19” x 8”
IMPORTANT SAFETY INSTRUCTIONS
5
ENGLISH
CAUTION -
Please read before use and keep for future reference.
A4 A5
1. Ensure the machine is on a stable
surface. Lift the punch handle to its
upright position.
BEFORE YOU BIND
2. Lift the punch handle. Check the
waste tray is empty and correctly fitted.
3. Ensure the comb-opening mechanism
is closed.
STEPS TO BIND
1. Select either A4 or A5 paper size and
test punch scrap sheets. Select the cor-
rect comb diameter to suit the document
(see chart).
2. Place the binding comb into the
opening mechanism and fully engage
the opening plate by sliding the comb
to the left.
3. Open the binding comb by turning the
comb lever. Take care not to open the
comb too far.
1. Insert sheets fully into the punch slot.
Align the sheets to the edge guide.
2. When all punched sheets are loaded
onto the comb, close the comb lever.
3. To remove the document, slide the
comb to the right and lift up the docu-
ment.
TROUBLESHOOTING
Problem Possible cause Solution
Punched holes are not central Edge guide not set Adjust edge guide until hole pattern is correct
Machine will not punch Blockage Check waste tray is empty. Check for blockage to paper entry
Punch holes are not parallel to edge Debris is stuck below dies
Take stiff cardboard and slide into the paper entry. Move the cardboard
sideways to release any stray clippings into the waste tray
Partial holes Sheets not correctly aligned to punch pattern Adjust edge guide and test punch scrap sheets until correct
Damaged hole edges Possibly overloading the machine
Punch plastic covers with paper sheets. Reduce number of sheets being
punched
Waste tray leaks
Waste tray is not correctly inserted or ‘burst feature’
has activated
Check waste tray is empty and ‘burst feature’ is closed
Cannot access document measure feature Document measure is part of the waste tray
Check punch handle is fully raised then remove the waste tray & docu-
ment measure
A4 A5
A 4 A 5
A 4 A 5
A 4 A 5
1
2
3
6
5
LOCATION OF CONTROLS
1. Punch handle 5. Waste tray
2. Edge guide selector 6. Document measure
3. Edge guide 7. Comb lever
4. Paper entry
COMB DIAMETER & DOCUMENT SIZES
LIGHT USE
16
MM
MAX COMB SIZE
12
SHEETS
PUNCH CAPACITY
120
SHEETS
BIND CAPACITY
4
7
LOCATION OF CONTROLS
6mm
1/4” 8mm
5/16”
10mm
3/8”
12mm
1/2”
16mm
5/8”
2-20 sheets 21-40 sheets 41-55 sheets 56-90 sheets 91-120 sheets
3
SET UP
S_407888_RevC_25L_103116.indd 3-5 10/31/16 4:27 PM