background image

Page 3

 

VictoryLX 3-leg 

Assembly

Step #1: attach top supports to frame

The two top supports are left and right specific. The short end of each top support must be on  

the same side of the frame as the longer frame channel at the open end of the frame segment.

•  Insert the latches on the top support into the keyhole slots at the end of the frame channels.

•  Tap the top support to fully seat it against the frame. 

•  Repeat to attach the top support on the other frame segment. 

Step #2: assemble frame

With the table top facing down on a soft, clean surface, use the center leg bracket to connect the two frame segments. 

•  Loosen the eight set screws on each of the frame segments. 

•  Attach the center leg bracket to the left frame segment. The longer section of the cross channel at the open end should be at the top, toward the rear of the table.

 

— Align the 90°, 120°, or 180° holes on the bracket with the two holes on the ends of each channel, as shown. This example is a 120° table. 

 

— Adjust the channels as necessary to align the holes. 

•  Secure the bracket to the left frame segment with four M6x15 socket cap screws. Use the 5mm Allen key to tighten the screws.

•  Repeat this procedure to attach the right frame segment.

5mm Allen 

key

longer channel

section

loosen all

set screws

M10x16

left frame

segment

center leg bracket

align

holes

5mm Allen 

key

repeat for

right frame segment

M6x15 socket cap

short end

longer channel

top support

frame

channels

tap to firmly

seat top support

Содержание ESI Victory 3V-LX-C4848-24 Series













Отзывы: