9
en
Original Instructions for radius grinding module.
Symbols, abbreviations and terms used.
The symbols in the Instruction Manual and on the
machine shall aide in directing your attention to possible
hazardous situations when working with this machine.
For your safety.
Do not use this machine before you have thor-
oughly read and completely understood these
operating instructions, including the figures, speci-
fications, and safety regulations.
Read and observe the Instruction Manuals of the
GI150/GI1502H belt grinder as well as the GIB/
GIBE undercarriage that are to be mounted to this
machine.
These operating instructions should be kept for later use
and enclosed with the power tool, should it be passed on
or sold.
Use only the fastening material provided for mounting the
radius grinding module to the belt grinder.
When mounted
incorrectly, the radius grinding module can loosen itself
from the belt grinder during the working procedure and
lead to serious injuries.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debris generated by various operations. The
dust mask or respirator must be capable of filtrat-
ing particles generated by your operation. Pro-
longed exposure to high intensity noise may cause
hearing loss.
Make sure that all clamping levers and clamping fixtures
are firmly tightened.
If the machine suddenly starts to
lower itself or if the work piece becomes loose during
the working procedure, serious injuries can result.
At a glance.
1 Cover/stop (GI 150/GI 150 2H)
2 Spark guard (GI 150/GI 150 2H)
3 Grinding rest (GI 150/GI 150 2H)
4 Dust collector (GI 150/GI 150 2H)
5 Side cover (GI 150/GI 150 2H)
6 Lever for swivel device (GIB/GIBE)
7 Counter-plate
8 Angled-plate
9 Bolts for angled-plate
10 Bolts for counter-plate
11 Belt tension lever (GI 150/GI 150 2H)
12 Mounting bolts for side assembly
13 “Centre height” adjustment lever (pipe centre)
14 Clamping lever for “Centre height” adjustment
15 “Grinding depth/depth stop” adjustment
16 Crank for adjustment of work piece width
17 Collection receptacle
18 Work piece quick-clamping lever
19 Clamping jaws, fixed
20 Mounting bolts
21 Holding device/magazine for contact rollers
22 Star-knob bolt, height adjustment
23 Protective covers/side cover
24 Contact roller
25 Locking screw for contact roller
26 Clamping lever for angle adjustment
27 Mounting screws for alignment of radius grinding mod-
ule/belt grinder
Intended use of the machine.
The radius grinding modules GIR are to be used together
with the GI150/GI1502H belt grinder and exclusively for
grinding off pipe ends.
Work pieces with a diameter smaller than 35 mm
may not be processed with the GI 150 belt grinder!
Mounting instructions (Figure 1/2).
Belt grinder GI 150 2H.
Before any work on the machine itself, pull the power
plug from the socket outlet.
➤
Dismount the top cover (1) together with the spark
guard (2).
➤
Dismount the grinding rest (3) and the dust collec-
tor (4).
➤
Open the side cover (5).
➤
Loosen the belt tension lever (11) and remove the
grinding belt.
➤
Close the side cover.
Undercarriage GIB/GIBE.
➤
Loosen the lever for the swivel device (6) and posi-
tion the GI150/GI1502H approx. level.
GIR.
➤
Take the module out of the packaging and mount the
accessories as described in the data sheet.
➤
Loosen the four mounting bolts (20) of the upper
part at the front and rear of the foot pedestal.
➤
Loosen the four bolts (9) and slide the angled-
plate (8) down.
➤
Slide the GIR against the GI150/GI1502H belt
grinder.
➤
Bolt the GIR to the GI150/GI1502H from the side-
with the 4 bolts (12). Loosen the swivel device of the
undercarriage again if the holes are not aligned.
➤
Slide the angled-plate (8) against the bottom side of
the GI150/GI1502H and tighten the four bolts (9).
Symbol
Term, meaning
➤
Action
General mandatory sign
Read documentation
Danger warning
European conformity symbol
3 94 10 005 00 0.book Seite 9 Donnerstag, 3. November 2011 12:42 12
