16
en
For your safety.
Read all safety warnings and all
instructions.
Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
Hand-guided nibbler for cutting sheet metal, cut-outs
and tight curves in weather-protected environments
without water supply using the application tools and
accessories recommended by FEIN.
This power tool is also suitable for use with AC gener-
ators with sufficient power output that correspond to
the Standard ISO 8528, design type G2. This Standard
is particularly not complied with when the so-called dis-
tortion factor exceeds 10 %. When in doubt, please
refer to the generator instruction/specification guide.
Special safety instructions.
Use auxiliary handle(s), if supplied with the tool.
Loss
of control can cause personal injury.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. Where appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments.
The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask or res-
pirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high inten-
sity noise may cause hearing loss.
The application tools are sharp. Never place your hand
near the application tools.
Touching application tools
can lead to injuries.
U
V
V
Rated voltage
f
Hz
Hz
Frequency
M...
mm
mm
Size of metric thread
Ø
mm
mm
Diameter of a round part
mm
mm
Max. work-piece thickness for steel with up to
400 N/mm
2
mm
mm
Max. work-piece thickness for steel with up to
600 N/mm
2
mm
mm
Max. work-piece thickness for steel with up to
800 N/mm
2
mm
mm
Max. work-piece thickness for aluminium with up
250 N/mm
2
mm
mm
Diameter of pilot-drill for inside cut-outs
mm
mm
Min. inside curve radius
kg
kg
Weight according to EPTA-Procedure 01
L
pA
dB
dB
Sound pressure level
L
wA
dB
dB
Sound power level
L
pCpeak
dB
dB
Peak sound pressure level
K...
Uncertainty
m/s
2
m/s
2
Vibrational emission value according to EN 62841
(vector sum of three directions)
h
m/s
2
m/s
2
Vibrational emission value
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
Basic and derived units of measurement from the
international system of units
SI
.
Character
Unit of measure-
ment, international
Unit of measure-
ment, national
Explanation
Fe 400
Fe 600
Fe 800
Al 250
WARNING
Содержание BLK3.5E
