19
en
For your safety.
Read all safety warnings and all
instructions.
Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
hand-held drill for drilling in metal, wood, plastic,
ceramics, and for tapping in weather-protected envi-
ronments using the application tools and accessories
recommended by FEIN.
The hand-held drill is not intended for working carbon
fibre reinforced plastics.
Safety warnings for drills.
Safety instructions for all operations.
Use the additional handle (s).
Loss of control can lead
to injury.
Hold the power tool by the insulated gripping surfaces
when performing operations where the application tool
could contact hidden wiring.
Contact with a “live” wire
will also make exposed metal parts of the tool “live”
and shock the operator.
Safety instructions when using long drill bits.
Never operate at higher speed than the maximum speed
rating of the drill bit.
At higher speeds, the bit is likely
to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip in
contact with the workpiece.
At higher speeds, the bit is
likely to bend if allowed to rotate freely without con-
tacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do not
apply excessive pressure.
Bits can bend causing break-
age or loss of control, resulting in personal injury.
Special safety instructions.
Beware of any concealed electric cables, gas or water
conduits.
Check the working area before commencing
work, e. g. with a metal detector.
Secure the work piece firmly.
A work piece that is
gripped tightly in a clamping device or vice, is more
secure than if held by hand.
Hold the power tool firmly.
High reaction torque can
briefly occur.
Do not direct the power tool against yourself, other per-
sons or animals.
Danger of injury from sharp or hot
application tools.
Do not rivet or screw any name-plates or signs onto the
power tool.
If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Do not use accessories which are not specifically
designed and recommended by the power tool manu-
facturer.
Safe operation is not ensured merely because
an accessory fits your power tool.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. Where appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments.
The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask or res-
pirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high inten-
sity noise may cause hearing loss.
Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
When working overhead, beware of falling objects,
such as chips.
To prevent injuries, always keep your hands, clothing,
etc. away from rotating swarf.
The swarf can cause inju-
ries.
Do not attempt to remove the cutting tool if it still turns.
This can lead to serious injuries.
Clean the ventilation openings on the power tool at reg-
ular intervals using non-metal tools.
The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Do not work with materials containing magnesium.
Danger of fire.
Do not work with CFRP (carbon-fiber-reinforced poly-
mer) and materials containing asbestos.
These materi-
als are considered carcinogenic.
Use and handling of the battery (battery pack).
To avoid hazardous situations such as burns, fire,
explosion, skin injuries, and other injuries when han-
dling the battery, observe the following instructions:
Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact
or shock.
Hazardous vapours and fluid can escape in
case of damage and improper use of the battery. The
vapours can irritate the respiratory system. Liquid
ejected from the battery may cause skin irritations or
burns.
When battery fluid from a damaged battery has come
into contact with objects close by, check the respective
components, clean them or replace them as required.
Keep the battery away from heat and fire. Do not store
the battery in direct sunlight.
Do not remove the battery from its original packaging
until it is going to be used.
WARNING
Содержание ABOP10
