Fein 60250 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

Fein 60250 Скачать руководство пользователя страница 11

11

LUBRICATION

See Fig. 24

This tool has been properly lubricated and is ready to use.

The recommended grease: Mobil HD 85W/140 Oil.

Add the oil

Check oil level of the gear case once a year. Follow the

procedure below to check and fill the oil. Unplug the

the tool. Place the saw on a horizontal position.

Use the 5mm HEX wrench to loosen the screw and

removing the oil plug, using a small funnel [spout size is

less than 3/16” (5mm).] Fill oil approximately 1.3 oz. (40cc),

avoid spilling by visual check. Please use the “

Mobil HD 85W/140

” oil,

Once filled, replace the oil plug with the 5mm HEX wrench, do not over tighten. The O-ring under

the head should be compressed slightly, over tightening will cause the O-ring to unseat and not

seal properly.

REPLACING CARBON BRUSHES

►

Caution: Turn off the switch and disconnect plug from power supply before checking.

REPLACE CARBON BRUSHES

Check brushes regularly, if worn down to 1/4” (6mm),

Replace brushes. Carbon brushes should be clean and

slide freely in holder. Carbon brushes should be replaced

in pairs. Use a flat blade screwdriver to remove the brush

cap (A), take out the worn carbon brush (B) insert new

carbon brush and secure the brush holder cap. Refer to

Fig.25

MAINTENANCE AND SERVICING

Disconnect tool from power supply before carrying out any

servicing and maintenance. Keep the machine clean. Never use a saw blade that is damaged or

distorted. Replace the saw blade when it becomes dull. For service and replacement pieces see the

replacement parts list and manufacturer website. Inspect the safety cover to assure that it is in good

condition and moves smoothly. Never use the tool unless the safety cover operates properly and it is

in good operating condition. After operation of the tool has been completed, make sure power plug

has been disconnected from the receptacle and store it in a secure place out of the reach of children.

Periodically remove chips in the chip cover and dust from the surface of the power tool with a damp

cloth. Keep the tool away from contact with water or oil.

Fig.25

Fig.24

«
...
9
10
11
12
13
...
»

Содержание 60250





















Отзывы:

Нет отзывов