5
Further safety instructions for all operations
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into
the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending on direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a)
Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque
reaction during start-up.
The operator can control torque reactions or kickback forces, if proper precautions
are taken.
b)
Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c)
Do not position your body in the area where power tool will move if kickback occurs.
Kickback will
propel the tool in direction opposite to the wheel’s movement at the point of snagging.
d)
Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the
accessory.
Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause
loss of control or kickback.
e)
Do not attach a saw chain woodcarving blade or toothed saw blade.
Such blades create frequent
kickback and loss of control.
Additional safety instructions for grinding and cutting-off operations
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations
a) Use only wheel types that are recommended for your power tool and the specific guard designed for
the selected wheel.
Wheels for which the power tool was not designed cannot be adequately guarded and
are unsafe.
b) The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip.
An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
c) The guard must be securely attached to the power tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the operator.
The guard helps to protect the operator from
broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.
NOTE the above warning may be omitted for grinders or cut-off grinders with a rated capacity of less than 55 mm.
d) Wheels must be used only for recommended applications. For example: do not grind with the side of
cut-off wheel.
Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these
wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not
suitable for the higher speed of a smaller tool and may burst.
Additional safety instructions for cutting-off operations
Additional Safety Warnings Specific for Abrasive Cutting-Off Operations
a)
Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive
depth of cut.
Overstressing the wheel increases the loading and susceptibility to twisting or binding of the
wheel in the cut and the possibility of kickback or wheel breakage.
b)
Do not position your body in line with and behind the rotating wheel.
When the wheel, at the point of
operation, is moving away from your body, the possible kickback may propel the spinning wheel and the
power tool directly at you.
c)
When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-
off wheel from the cut while the wheel is in motion otherwise kickback may occur.
Investigate and take
corrective action to eliminate the cause of wheel binding.
d)
Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-
enter the cut.
The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.
e)
Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both sides of the wheel.
f)
Use extra caution when making a “pocket cut” into existing walls or other blind areas.
The protruding
wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
