manualshive.com logo in svg

Fei Bao MiG-21 Fishbed, Инструкция по эксплуатации

Поделиться
Скачать
Fei Bao MiG-21 Fishbed Скачать руководство пользователя страница 7

Fei Bao MiG-21 Fishbed Instruction Manual (Draft Rev 0) 

Page 7 of 24 

 

 

Nose Wheel Steering Servo Installation 
 
Using  3mm  bolts  and  blue  Loctite,  install  the  NWS  servo  mounts  into  the  plated  steel  frame 
attached to the nose gear strut.  Adjust the NWS pushrods to the correct length to engage the 
servo arm and connect the NWS pushrods to the servo. 
 

 

 

 
 
Flap Servo and Control Horn Installation 
 
The  plywood  mounts  for  the  flap  servos  are  also  preinstalled.  The  servos  are  mounted  to  the 
supplied  CF  angles  which  are  pre-drilled  to  accept  the  3mm  supplied  mounting  screws.  This 
assembly is then positioned in the servo cutout, 1/16" pilot holes drilled in the plywood mounts, 
and the assembly is screwed down. 
 
The flap control horn needed to be modified by grinding it away slightly at the front (see rudder 
control horn section) such that it fit properly in its precut slot. Be sure to sand the sides of the 
horn before Hysol'ing it into place. 
 
Connect  the  flap  control  horn  to  the  servo  arm  using  the  provided  hardware  or  the  builder’s 
preferred hardware.  Final adjustment of the pushrod, centering the flap, and installation of the 
servo cover will be done when setting up the control throws. 
 

Содержание MiG-21 Fishbed

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды