2. Connect the 14-gauge red wire to the (+) positive
terminal of the battery using an in-line, user-supplied fuseholder
and 25A fuse (15A fuse for 24V model). Locate the fuse as near the
battery as possible to protect the entire length of wire.
NOTE
All directional lamps will illuminate simultaneously if
the power supply leads are reversed. Correct the wiring
before proceeding.
3. Read and understand paragraph IV OPERATION,
and test for proper operation of all functions.
IV.
OPERATION.
SAFETY MESSAGE TO OPERATORS
Peoples’ lives depend on your safe use of our
products. Listed below are some important safety
instructions and precautions you should follow:
•
Although your warning system is operating
properly, it may not be completely effective.
People may not see or heed your warning sig-
nal. You must recognize this fact and continue
driving cautiously.
•
Also, situations may occur which obstruct your
warning signal when natural or man-made
objects are between your vehicle and others,
such as: raising your hood or trunk lid. If these
situations occur, be especially careful.
•
This product contains high intensity LED de-
vices. To prevent permanent eye damage, DO
NOT stare into the light beam at close range.
•
At the start of your shift, you should ensure
that the light is securely attached and all
lamps are operating properly.
•
If a selected function does not perform prop-
erly or if any of the lamps remain illuminated
when the control is off, disconnect the power
connector from the control unit and contact
the nearest service center.
Failure to follow these safety precautions may result
in property damage, serious injury, or death to you, to pas-
sengers, or to others.
RETAIN AND REFER TO THIS MESSAGE
H3 (
-
) BLACK GROUND TO CHASIS OR BATTERY
H2 RED +12V TO LIGHT HEADS
H1 RED +12V,
FUSED
H4 RIGHT TURN SIGNAL (OPTIONAL)
H5 LEFT TURN SIGNAL (OPTIONAL)
CABLE TO LAMPS
CONTROL CABLE
290A5169
Figure 3.
A.
On/Off Switch.
1. OFF Position.
The SignalMaster is not powered and the turn sig-
nal/brake feature (if installed) is functional.
2. ON Position.
a. The switch will illuminate. If the switch does
not illuminate, check the connection of the brown control wire.
b. The directional/hazard patterns will operate as
selected by the Hazard Rocker Switch.
B.
Hazard Rocker Switch.
NOTE
These patterns will override the turn signal/brake fea-
ture (if installed).
1. LEFT Position.
In this position, the light produces a left arrow
flashing pattern, instructing traffic to move left.
2. CENTER Position.
In this position, an alternating pattern is produced.
The four middle lights activate alternately with the two outside
lights on each side.
3. RIGHT Position.
In this position, the light produces a right arrow
flashing pattern, instructing traffic to move right.
C.
Turn Signal/Brake Option.
1. Turn Signal.
If installed, a single end lamp flashes in sync with
the vehicle turn signal.
2. Brake.
If installed and the vehicle uses a common brake/
turn wire, both end lamps illuminate with the vehicle brake lights.
Damage to the directional light assembly will occur if
this vehicle is jump-started when the light is “on”. Ensure
that the light is switched “off” before jump-starting this
vehicle.
V. MAINTENANCE.
A.
General.
Crazing (cracking) of lenses will cause reduced ef-
fectiveness of the light. Do not use cleaning agents
(which will cause crazing) such as strong deter-
gents, solvents, or petroleum products. If crazing of
lenses does occur, reliability of light for emergency
signalling purposes may be reduced until lenses
are replaced.
Ordinary cleaning of the plastic lenses can be accom-
plished by using mild soap and a soft rag. Should fine scratches
or a haze appear on a lens, they can ordinarily be removed with a
non-abrasive, high quality, one-step, automotive paste cleaner/wax
and a soft cloth.
-3-
