Federal Signal Corporation DSA1X Скачать руководство пользователя страница 17

Страница: 17 / 20

Installation

Description, Specifications, and Installation Manual

Mounting without Bracket

You can mount the speaker directly to the mounting surface without the bracket. Use

installer-supplied 1/4-20 fasteners that are suitable for the mounting surface. Use

Figure 10 for the hole center dimensions.

Figure 11 Surface mount hole center dimensions

5.20 in

2.60 in

3.00

6.00

7.39

(6) 1/4-20

0.5 in THREAD DEPTH

Opening the Housing

Tools required:

3/8 in socket
6 in extension
To open the housing, loosen the four cover screws while supporting the housing so it

does not fall. (The cover screws are retained in the housing.) The front of the unit is

heavy, but it is attached to the rear housing with a pivot hinge to allow ease of service.

If the unit requires service, replace the front housing, amplifier, and power supply (if

equipped) as an entire unit.

Содержание DSA1X





















Результаты поиска

Содержание DSA1X

Отзывы:

Похожие инструкции для DSA1X

Бренды по названию

Популярные бренды

Federal Signal Corporation DSA1X, Описание, характеристики и руководство по установке

Результаты поиска

Содержание DSA1X

Отзывы:

Похожие инструкции для DSA1X

Бренды по названию

Популярные бренды