manualshive.com logo in svg

Federal Signal Corporation DSA1X, Описание, характеристики и руководство по установке

Поделиться
Скачать
Federal Signal Corporation DSA1X Скачать руководство пользователя страница 14

14

  

  

Installation

DSA1X Speaker

Pole Mounting 

The DSA1X comes standard with a bracket for vertical wall or ceiling mount. The 

optional I-IP100-PMW kit or I-IP100-PM kit is required for pole mounting. 

Large Pole Mounting (6 in diameter or larger)

Use the following procedure if mounting the speaker with the optional I-IP100-PMW 

bracket:
1.  Find suitable location to mount speaker. Use industry or company preferred practices 

when mounting hardware to poles or other structures.

2.  Attach the I-IP100-PMW bracket to the pole using banding or use the pre-drilled 

holes to bolt the bracket to the pole or structure.

3.  Using the supplied flat washers, lock washers, and 3/8 in nuts, mount the speaker to 

the I-IP100-PMW bracket as shown in Figure 2.

4.  Use the side pivot bolts to allow adjustment of the speaker up and down to optimize 

speaker effectiveness.

Figure 8 Bracket I-IP100-PMW

  

Содержание DSA1X





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды