Federal Signal Corporation CP-BG Series Скачать руководство пользователя страница 17

Страница: 17 / 24

Federal Signal

signaling.fedsig.com

Figure 21 Replacing the glass

APPLY PRESSURE ON

BOTTOM EDGE AT

TRIANGLES AND

ANGLE IN

REPLACEMENT PANEL

TOWARDS 3 RETURN

SPRINGS

REPLACEMENT

PANEL HELD IN

PLACE BY TWO

CORNER

BOSSES

AGAINST 3

COMPRESSION

SPRINGS

ACTIVATION INDICATOR IN

ALARM STATUS MODE

Reattach the front faceplate.

Note that the activation indicator is in ALARM status mode. With the reset keyway attached, rotate the indicator

about 60° counter-clockwise if it is desired to return to NORMAL status mode.

Figure 22 Returning to a normal state

MODEL CP-BG: NORMAL STATE

RESET KEYWAY

MAY ONLY

REMAIN

ATTACHED ON

CP-BG MODELS

Installing/Servicing the Reset Keyway

The reset keyway is factory-attached on the CP-PB and CP-BG stations. On the CP-BG-x-x-x-xxx-xx-2 (E54-11 approved)

stations, it is provided separately to be used only as a discrete standalone key. On these models, the key should not be

permanently installed for EN-54-11 installations and shall be used only for test purposes. Its purpose is twofold:

Provide a means of resetting all devices after an activated ALARM status by a 60° counter-clockwise rotation of

the activation indicator.

Provide a means of ALARM activation testing of the CP-BG stations without breaking the glass panel.

Figure 23 Reset keyway kit

RESET KEYWAY KIT

M4 SET SCREW (USE A

M2 HEX WRENCH TO

TIGHTEN/LOOSEN)

DIRECTIONAL STATUS

INDICATOR

BEARING WASHER TO

BE BETWEEN STATION

AND RESET KEYWAY

Figure 24 Keyway location

Figure 30

Содержание CP-BG Series

























Результаты поиска

Содержание CP-BG Series

Отзывы:

Похожие инструкции для CP-BG Series

Бренды по названию

Популярные бренды

Federal Signal Corporation CP-BG Series, Руководство пользователя

Результаты поиска

Содержание CP-BG Series

Отзывы:

Похожие инструкции для CP-BG Series

Бренды по названию

Популярные бренды