background image

iii 

SAFETY NOTICES

 

 

 

People’s lives depend on your safe installation, service and operation of our products.  It is 
important to read, understand and follow all instructions shipped with this product. In addition, 
listed below are some other important safety instructions and precautions you should follow: 
 
 

INSTALLATION & SERVICE 

 

 

Electrocution or severe personal injury can occur when performing various installation and 
service functions such as making electrical connections, drilling holes, or lifting equipment. 
Therefore experienced electricians in accordance with national, state and any other electrical 
codes having jurisdiction should perform installation. All work should be performed under 
the direction of the installation or service crew safety foreman. 

 

 

The sound output of sirens is capable of causing permanent hearing damage. To prevent 
excessive exposure, carefully plan siren placement, post warnings and restrict access to areas 
near the sirens. Sirens may be operated from remote control points. Whenever possible, 
disconnect all siren power including batteries before working near the siren. 

 

 

After installation or service, test the siren system to confirm that it is operating properly. Test 
the system regularly to confirm that it will be operational in an emergency. 

 

 

If future service personnel do not have these warnings and all other instructions shipped with 
the equipment to refer to, the siren system may not provide the intended audible warning and 
service personnel may be exposed to death, permanent hearing loss, or other bodily injury. 
File these instructions in a safe place and refer to them periodically. Give a copy of these 
instructions to new recruits and trainees. Also, give a copy to anyone who is going to service 
or repair the sirens. For additional copies, call the Federal Warning Systems Customer Care 
Center at 800-524-3021 or write to them at 2645 Federal Signal Drive, University Park, IL 
60484-3167. 

 

OPERATION 

 

 

Failure to understand the capabilities and limitations of your siren system could result in 
permanent hearing loss, other serious injuries or death to persons too close to the sirens when 
you activate them or to those you need to warn. Carefully read and thoroughly understand all 
safety notices in this manual and all operations-related-items in all instruction manuals 
shipped with equipment. Thoroughly discuss all contingency plans with those responsible for 
warning people in your community, company, or jurisdiction. 

 
 
 
 
 
 

 

Содержание 2-240






























Отзывы: