CONFIDENTIAL
THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED.
© FC LIGHTING, INC.
FCSL2000 Series
- INSTALLATION INSTRUCTIONS
CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
DETAILED ILLUSTRATION
corporate
t
800.900.1730
f
630.889.8106
3609 Swenson Ave.
St. Charles, IL 60174
2458893
BRICK WALL INSTALLATION
GENERAL
:
1. Before starting the installation, make sure all electricity has
been turned off and electrical breaker has been locked out
and tagged out.
2. To ensure the success of the installation, be sure to read
these instructions and review the diagrams thoroughly
before beginning.
3. All electrical connections must be in accordance with local
codes, ordinances, or the National Electrical Code.
NOTE
: The important safeguards and instructions appearing in
this manual are not meant to cover all possible conditions and
situations that may occur.
IMPORTANT:
Temporarily remove Splatter Shield and contents
from Back Box housing and set aside.
1. Install (2) slotted Masonry Mounting Brackets onto each
side of the Back Box using (4) 6-32 adjustment screws
provided.
Orient Back Box as shown.
Fig 1
NOTE
: Ensure Back Box face is flush with Brick face.
Fig 2
2. Then fasten brackets to brick using appropriate hardware
(by others). Adjust Back Box vertical position for optimal
spacing between upper and lower bricks. Then tighten
adjustment screws.
3. Connect conduit to backbox using 3/4” K.O.s.
Fig 3
4. Reinstall Splatter Shield and all contents using the (2) 8-32
screws provided.
Fig 4
IMPORTANT
: All wiring connections must be made in
accordance with local electrical codes, ordinances, and the
National Electric Code.
Back Box Conduit Entry____
Foam Block Insert to
Retain Back Box Form
Splatter Shield
Wing Nuts
Threaded Rod
SL2000 Series
Universal Back Box
Concrete Pour Form
(by others)
(4) 3/4” Knockouts -
(2) on back and
(1) on each side
Fig 3
Masonry Mounting Brackets
Included w/ Back Box Kit
Flush Mounting to Brick Face
MOUNTING BRACKETS
BACKBOX
BRICK
Figure 4 (brick wall)
SPLATTER GUARD
Figure 6 (brick wall)
FLUSHED WITH FINISHED SURFACE
Figure 5 (brick wall)
BRICK
SL 2000 SERIES
BRICK WALL INSTALLATION
SL 2000 series backbox installation in
brick wall construction (Utility Brick
shown):
1. Install the (2) slotted mounting
brackets provided as shown in Figure
4, using the (4) 6-32 screws provided.
2. Adjust the brackets vertically for
optimal gap spaces between upper
and lower brick surfaces and back
housing
3. Orient fixture housing electrical
connections as directed on inisde
label. Failure to do so will result in
faceplate not installed in the correct
oreintation (critical STEP for SL2003,
SL2040, and SL2041 models).
4. Secure the mounting
brackets to the top of the brick
(hardware by others) so that the
front face of the back box will
be flush or slightly in front of the
finished wall surface after
installation (see Figure 5).
5. Connect conduit to backbox using
3/4” NPT fitting with teflon tape on
conduit. Pull wires into back housing for
electrical connections to be made
later.
6. Install Internal support block and
splatter guard provided as shown in
Figure 6, using the (2) 8-32 screws
provided securely and finish wall.
7. Before continuing, remove splatter
guard and debris from backbox to
allow for proper fitment.
FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW
Fig 2
Orient Back Box As Shown
6-32 adjusment
screws provided
MOUNTING BRACKETS
BACKBOX
BRICK
Figure 4 (brick wall)
SPLATTER GUARD
Figure 6 (brick wall)
FLUSHED WITH FINISHED SURFACE
Figure 5 (brick wall)
BRICK
SL 2000 SERIES
BRICK WALL INSTALLATION
SL 2000 series backbox installation in
brick wall construction (Utility Brick
shown):
1. Install the (2) slotted mounting
brackets provided as shown in Figure
4, using the (4) 6-32 screws provided.
2. Adjust the brackets vertically for
optimal gap spaces between upper
and lower brick surfaces and back
housing
3. Orient fixture housing electrical
connections as directed on inisde
label. Failure to do so will result in
faceplate not installed in the correct
oreintation (critical STEP for SL2003,
SL2040, and SL2041 models).
4. Secure the mounting
brackets to the top of the brick
(hardware by others) so that the
front face of the back box will
be flush or slightly in front of the
finished wall surface after
installation (see Figure 5).
5. Connect conduit to backbox using
3/4” NPT fitting with teflon tape on
conduit. Pull wires into back housing for
electrical connections to be made
later.
6. Install Internal support block and
splatter guard provided as shown in
Figure 6, using the (2) 8-32 screws
provided securely and finish wall.
7. Before continuing, remove splatter
guard and debris from backbox to
allow for proper fitment.
FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW
Fig 1
Align to face of
finished wall
Proper Orientation
Position
Proper
Orientation
Position
Back Box Splatter Shield____
Fig 4
Back Box
8-32 screws
provided
Foam Block Insert to
Retain Back Box Form
Splatter Shield
Wing Nuts
Threaded Rod
SL2000 Series
Universal Back Box
Concrete Pour Form
(by others)
BACKBOX
STUD
MOUNTING BRACKETS
Figure 2 (stud wall)
MOUNTING BRACKETS
BACKBOX
ADJUSTMENT SLOTS
Figure 1 (stud wall)
Figure 3 (stud wall)
SPLATTER GUARD
SL 2000 series backbox installation in hollow
(stud) wall construction (2” x 4” min.):
1. Install the (2) slotted mounting brackets
provided as shown in Figure 1, using the (4) 6-
32 screws provided.
2. Adjust the brackets (by loosening the
screws) so that the front face of the backbox
will be flush or slightly in front of the finished
wall surface after installation (see Figure 2).
3. Orient fixture housing electrical
connections as directed on inisde label.
Failure to do so will result in faceplate not
installed in the correct oreintation (critical
STEP for SL2003, SL2040, and SL2041 models).
4. Secure the mounting brackets to wood or
metal studs (hardware by others) so that the
front face of the back box will be flush or
slightly in front of the finished wall surface
after installation (see Figure 2).
5. Connect conduit to backbox using 3/4”
NPT fittings. Pull wires into back housing for
electrical connections to be made later.
6. Install splatter guard provided as shown in
Figure 3, using the (2) 8-32 screws provided
securely and finish wall.
7. Before continuing, remove splatter guard
and debris from backbox to allow for proper
fitment.
SL 2000 SERIES
STUD WALL INSTALLATION
FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW
