Fayat DYNAPAC SD2500C Скачать руководство пользователя страница 70

Страница: 70 / 580

B 38

EN standards

7.1

Continuous sound pressure SD2500C

The operator always must use ear protection. The emission value at the ear of the

driver varies depending on the materials used for paving and may even rise above

85 dB(A). If no ear protectors are used, hearing can be impaired.

The sound emission level of the paver finisher was measured under free-field condi-

tions according to EN 500-6:2006 and ISO 4872.

Sound pressure level at the operator’s position

(at the height of the head):

= 82.3 dB(A)

= 87 dB(A)

Sound capacity level:

= 105 dB(A)

= 104 dB(A)

7.2

Operating conditions during measurement

The diesel engine was running at maximum speed. The screed was lowered into

working position. The tamper and the vibrator were running at min. 50% of their max-

imum speed, the augers at min. 40% and the conveyors at min. 10% of their maxi-

mum speed.

T3:

BS IV & CS IV:

T3:

Содержание DYNAPAC SD2500C





































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DYNAPAC SD2500C

Отзывы:

Похожие инструкции для DYNAPAC SD2500C

Бренды по названию

Популярные бренды

Fayat DYNAPAC SD2500C, Руководство по эксплуатации

Результаты поиска

Содержание DYNAPAC SD2500C

Отзывы:

Похожие инструкции для DYNAPAC SD2500C

Бренды по названию

Популярные бренды