Fayat DYNAPAC SD2500C Скачать руководство пользователя страница 35

Страница: 35 / 580

B 7

Crossbeams / screed lifting device:

The screed lifting device is used to lift the

screed during transportation. The screed's approach angle can be changed using the

eccentric adjustment facility on the crossbeam.

Depending on the paving condition requirements, the crossbeam can be moved

backwards or forwards. This adjustment enlarges the material space between the au-

ger and screed.

Automatic paving stop and screed chargi ng/relieving:

The automatic paving stop

prevents the formation of any screed marks caused by a stopped screed. When the

paver finisher stops (during a truck change), the screed remains in floating position

and relief pressure is applied, thus preventing the screed from sinking while station-

ary.

The screed relieving device puts a higher load on the traction unit, thus increasing

the traction.

Activating the screed charging device can improve the compacting result under dif-

ferent paving conditions.

Central lubricating system (

The central lubrication pump fitted with a large lu-

bricant tank supplies grease to the various lubrication circuits through various flow di-

viders. They supply lubricant to the service-sensitive points of lubrication (e.g.

bearings) at adjustable intervals.

Содержание DYNAPAC SD2500C





































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DYNAPAC SD2500C

Отзывы:

Похожие инструкции для DYNAPAC SD2500C

Бренды по названию

Популярные бренды

Fayat DYNAPAC SD2500C, Руководство по эксплуатации

Результаты поиска

Содержание DYNAPAC SD2500C

Отзывы:

Похожие инструкции для DYNAPAC SD2500C

Бренды по названию

Популярные бренды