Fayat Dynapac DFP6 Скачать руководство пользователя страница 76

Страница: 76 / 116

8.1 Preliminary remarks and safety notes

DANGER!
Danger to life caused by an operationally

unsafe machine!

–

The machine must only be serviced by quali-

fied and authorized personnel.

–

Follow the safety regulations for maintenance

work

Chapter 3.9 „Maintenance

work“ on page 34

WARNING!
Health hazard caused by fuels and lubricants!

–

Safety regulations and environmental protec-

tion regulations must be followed when han-

dling fuels and lubricants

Chapter 3.4 „Han-

dling fuels and lubricants“ on page 25

Wear your personal protective equipment.

Do not touch hot components.

Park the machine on horizontal, level, firm ground.

Perform maintenance work only with the engine shut down and the

spark plug connector disconnected.

Make sure that the engine cannot be accidentally started during

maintenance work.

Thoroughly clean machine and engine before starting maintenance

work.

Do not leave any tools or other objects, that could cause damage,

in or on the machine.

After maintenance work has been completed, dispose of fuels and

lubricants, filters, sealing elements and cleaning cloths in an envi-

ronmentally friendly way.

After all maintenance work is completed reinstall all guards and

safety installations.

Maintenance – Preliminary remarks and safety notes

DFP6

Содержание Dynapac DFP6





















































































































Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды

Fayat Dynapac DFP6, Инструкция по эксплуатации

Результаты поиска

Содержание Dynapac DFP6

Отзывы:

Бренды по названию

Популярные бренды