manualshive.com logo in svg

Faulhaber MC 5004 P STO, Руководство по установке

Поделиться
Скачать
Faulhaber MC 5004 P STO Скачать руководство пользователя страница 54

1st edition, 03-05-2018

7000.05063, 1st edition, 03-05-2018

7000.05063

Installation

54

4.3

Information on initial commissioning

During the initial commissioning, the correct function of the entire safety circuit must be 
tested and documented.

DANGER

DANGER

!

Errors during the installation and commissioning of the Motion Controller could impair its 
safety function.

If safety functions are unavailable, the drive can start up unexpectedly or shutdown of the

torque may be ineffective. Depending on the use of the Motion Controller, this can lead to

severe or fatal injury.

Observe the safety information in the chap. 2.2.2, p. 10.

Prior to the initial commissioning, also take the following measures:

Ensure that all operating materials within the safety circuit are professionally installed 
and functional.

Check all electrical connections.

Visually inspect all safety-relevant components.

If necessary, take additional safety measures to protect persons from danger during the 
initial commissioning which could arise from incorrect function of the safety circuit.

When started, the Motion Controller performs an automatic self-test. An error message is 
output if the self-test fails.

When starting the Motion Controller, pay attention for error and STO status messages.

Do not commission a Motion Controller whose self-test has failed.

Perform a self-test daily (see chap. 2.4, p. 11).

During commissioning, check whether the following results are achieved (see 
chap. 3.4.1.3, p. 20):

D

The configuration and commissioning of the Motion Controller are described in the 
manuals for the Motion Manager 6 and the drive functions (see chap. 1.2, p. 5).

Test criterion

Test result

STO In 1 = high, STO In 2 = high

STO Off

STO In 1 = high, STO In 2 = low

STO On

STO In 1 = low, STO In 2 = high

STO On

STO In 1= low, STO In 2 = low

STO On

Switch-off time via STO In 1

<10 ms

Switch-off time via STO In 2

<10 ms

Power consumption during STO On

<1500 mW

Содержание MC 5004 P STO






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды