manualshive.com logo in svg

Faulhaber MC 5004 P STO, Руководство по установке

Поделиться
Скачать
Faulhaber MC 5004 P STO Скачать руководство пользователя страница 31

1st edition, 03-05-2018

7000.05063, 1st edition, 03-05-2018

7000.05063

Installation

31

4.2.4

Connection of the power supply

Discrete inputs and outputs (for instance for discrete target values preselection or for 
connection of limit switches / reference switches)

Communication connections

Make sure that the connection cables to the connection side are not longer than 3 m.

Keep the screen connections for connection cables short and flat.

To reduce the effects on the DC power supply network, ferrite sleeves (such as WE 742 700 
790) can be fitted on the supply cables.

Fig. 17: EMC protective circuit

4.2.4.1

Power supply

Connect the Motion Controller to a sufficiently well dimensioned power supply unit.

During acceleration procedures, current peaks with values up to the peak current limit 
setting of the motor can occur for multiples of 10 ms.

During braking procedures, energy can be regenerated and fed back into the DC power 
supply network. If this energy cannot be taken up by other drives, the voltage in the DC 
power supply network will rise. A limit value for the voltage that can be fed back dur-
ing regenerative braking can be set in the Motion Controller. Alternatively the overvolt-
age can be dissipated by an additional external Brake Chopper, see the datasheet for 
the Brake Chopper.

The USB port is a pure configuration connection. A cable length of < 3 m also applies 
to the USB connection.

L1

D1

GND

Motor

Int. 

S

upply

U

P

Содержание MC 5004 P STO






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды